[Public-List] Hello from Vancouver. (Somewhat)proud newowner of Antares 1967 A30.

[Glennb]

jeremy,
Main thing with the new chainplates Is to check to see if that the bolts are 5/16" or larger...The original ones where 1/4"' which provided to be to small for the shearing loads imposed on the rigging.

Glenn P.
Dolce 318  

Sent from my iPad

On Jul 27, 2012, at 10:07 PM, Jeremy Brown <j_l_brown at shaw.ca> wrote:

> Hmm.  My understanding was the reverse, that the middle two were year, didn't think they still made them by 84?
> 
> Before I forget, Re: chain plates, mine appear already upgraded, with stainless backing plates on opposite side etc.  One owner really loved her, a later one sadly abused her quite badly.  
> 
> 
> 
> Gordon Laco <mainstay at csolve.net> wrote:
> 
> Hi Jeremy
> 
> That number indicates you've got an Alberg 30, hull number 693, built in '82
> 
> Gord #426 Surprise. (3042670)
> 
> On 2012-07-28, at 5:26 AM, Jeremy Brown <j_l_brown at shaw.ca> wrote:
> 
>> Should I still remove tabbing since it is unbroken?  I have pictures of my mast step and the sticker on it which is all I could find for identifying marks, blue water spars out of north Vancouver.  Hull plate says 3069382, so I suppose I'm hull 382, anyone know any history on it?
>> 
>> 
>> Thanks
>> 
>> Jeremy
>> 
>> Mike Lehman <sail_505 at hotmail.com> wrote:
>> 
>> Jeremy
>> 
>> You are welcome. I look forward to getting progress reports. Mike Meinhold, 
>> owner of #272, commented that you should not loosen the rigging too much at 
>> a time, only enough to put slack in the rig, then jack up the beam until the 
>> rigging is tight, then loosen the rigging some more, etc. He learned this 
>> the hard way earlier this year.
>> 
>> I would not worry about deforming the deck...just take it slow.
>> 
>> 
>> 
>> Mike Lehman
>> 
>>> <((((º>`·.¸¸.·´¯`·.¸><((((º>`·.¸¸.·´¯`·.¸><((((º>
>> -----Original Message----- 
>> From: Jeremy Brown
>> Sent: Friday, July 27, 2012 11:43 AM
>> To: Alberg 30 Public List -- open to all
>> Subject: Re: [Public-List] Hello from Vancouver. (Somewhat)proud newowner of 
>> Antares 1967 A30.
>> 
>> Thank you so much:)  that's going to be so valuable when it comes time to do 
>> it.
>> That's exactly my suspicion with the screws.
>> 
>> My understanding of the depression was exactly that, but the tabbing on the 
>> back is totally unbroken, and the deck has no depression.  A different 
>> surveyor and two experienced boat people looked at it.  They were puzzled by 
>> the obvious depression in the underside as the deck looks perfect on top. 
>> One said that the way the fiberglass tape goes around the trim, and the 
>> other edges make it appear that the deck was cut out and returned inside 
>> only.
>> I'm worried about distorting the outside deck when I move it back into 
>> place.
>> 
>> 
>> 
>> 
>> Mike Lehman <sail_505 at hotmail.com> wrote:
>> 
>> Jeremy
>> 
>> The long screws through the bottom provide no support at all. Once they are
>> removed you may find that the delamination is more pronounced, if the screws
>> are holding the layers together.
>> 
>> An understanding of how the beam was originally constructed and why it
>> failed is helpful to understand how it can be repaired.
>> 
>> 1. Whitby Boat works used the wrong kind of glue to laminate the beam. Maybe
>> it was the only kind available at the time the boats were manufactured. The
>> glue failed and the laminations s
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

 1343543080.0