[alberg30] coating rudder hardware

[David Swanson]

Joe -

My boat had the same set up, except no one had replaced the dead
electronics, they just left the transducers.  I re-used the done for the
depth sounder, but not the speedo.  The speedo sender on my boat was
literally crumbling away, so I removed it & found that the actual hole in
the hull was very small - 1/2" or 5/8", I think.  Since I wasn't sure if I
would want to put in a speedo at a later date, I just bought a bronze bolt,
nut, & washers of the proper diameter & put that in the whole (with
appropriate sealant, of course.  It was a lot easier, cheaper, and I can
re-use the hole at a later date.

Just something to think about.

dls
Strayaway Child
Alberg 30 #229

alberg30 wrote:

> PS- while I'm at it, let me ask one more bottom question. #499 still has
> the original wood mounting pieces for an early model transducer and knot
> meter/ log. These are blocks of wood, one shaped like a fin, and another
> like a round block/cone. They appear to be sealed up and unused--with
> what I don't know.They have never leaked in the past. I've had new
> Horizon instruments pre-installed since I acquired the boat in 1996.
> Should I just leave them alone, or is there a reason to remove them and
> fiberglass up the bottom? I wonder if they'll rot off one day or maybe
> breakoff and leave a gaping hole(s) below the water line. Maybe glassing
> up their openings on the inside is the answer?
>
> Thanks for your help,
> Joe #499
> "One Less Traveled"
>
> ----- Original Message -----
> From: George Dinwiddie <gdinwiddie at min.net>
> To: <alberg30 at egroups.com>
> Sent: Monday, June 12, 2000 8:33 AM
> Subject: Re: [alberg30] coating rudder hardware
>
> > Joe,
> >
> > Are you talking about the straps of the pintles and gudgeons?  If so,
> > the putty over them is just to provide a fair surface.  I recommend
> using
> > something easy to remove.  You can mix up some West epoxy with West's
> > lightweight fairing filler (I don't recall the number) as one
> alternative.
> >
> >  - George
> >
> > > alberg30 said:
> > >
> > > I think I asked this once before-but can't find the post.
> > >
> > > On the rudder of #499 there is some black caulking ( now dried and =
> > > cracked) covering the rudder hardware. I think George said it was to
> =
> > > protect the pieces from corrosion or something.
> > >
> > > I can pretty much get the remains off--what do I put on in its
> place? =
> > > Would you recommend 3m 5200 (black) ,or is that over kill. Perhaps =
> > > another, less durable caulk would be better? Suggestions? Or maybe
> it =
> > > doesn't need to be covered at all.
> > >
> > > Thanks again;
> > >
> > > Joe #499
> > > "One Less Traveled"
> >
> > --
> >  ---------------------------------------------------------------------
> -
> >   George Dinwiddie                                  gdinwiddie at min.net
> >   The gods do not deduct from man's allotted span those hours spent in
> >   sailing.          http://ourworld.compuserve.com/homepages/Alberg30/
> >  ---------------------------------------------------------------------
> -
> >
> >
> >
> >
> >
>
> ------------------------------------------------------------------------
> Stand out.  In B2B. In Austin. Work with clients like Dell and pcOrder.
> Submit your resume to jobs at liaison.com. Visit us at
> http://click.egroups.com/1/4355/8/_/476031/_/960851519/
> ------------------------------------------------------------------------





 960872245.0