[Alberg30] Genoa Travler
Mike Lehman
sail_505 at hotmail.com
Thu Nov 27 09:06:51 PST 2003
Roger, You need to sail the boat for a couple of years before making this assumption. I have sailed my A30 for 26 years and have not found this to be true. Minor bumps do not affect the Alberg. What you are proposing is not a good idea. The strain on the deck will pull the joint apart. Ask Larry Morris whose previous owner had installed a pad-eye for a boom vang on the deck inside the toe rail. The stress on the eye pulled the deck up and compromised the deck/hull joint. Larry and I removed toe rail and track, then re-bed everything. I have been on many A30's that have pad-eyes on the rail thru bolted through the deck/hull joint and there has been no problems. Moving the track inboard also changes the sheeting angle and would not be considered legal under class racing rules.
----- Original Message -----
From: Roger L. Kingsland
To: Alberg 30 public list
Sent: Wednesday, November 26, 2003 2:28 PM
Subject: Re: [Alberg30] Genoa Travler
Mike;
Not to sound like Bill Clinton but, it depends on what your definition of
damage is. My argument is that, because the rail connector and the thru
hull fastener are the same assembly, even small bumps against the rail will
work the thru hull joint causing leaks and weakening of the joint. This
type of "damage" is not visible but how many boats leak at the toe rail?
Roger
Roger L. Kingsland, AIA
Managing Partner
Kingsland Scott Bauer Associates (KSBA)
N40° 27' 49" W79° 57' 59"
3441 Butler Street
Pittsburgh, PA 15201
www.ksba.com
1(412) 252-1500 X101 - Office & Voice Mail
1(412) 779-5101 - Mobile (no voice mail)
1(412) 252-1510 - Fax
----- Original Message -----
From: "Mike Lehman" <sail_505 at hotmail.com>
To: <public-list at alberg30.org>
Sent: Wednesday, November 26, 2003 11:51 AM
Subject: Re: [Alberg30] Genoa Travler
> Take it from someone who has hit a number of things with the Alberg over
the
> years - you gotta hit it pretty damn hard to cause any damage. Last
> encounter: 4-foot waves, 25+ knots and a BIG red channel marker. Ouch!
>
>
>
> Mike Lehman
> "Gilleleje" #505
>
>
>
>
>
> ----Original Message Follows----
> From: "Roger L. Kingsland" <rkingsland101 at ksba.com>
> Reply-To: Alberg 30 public list <public-list at alberg30.org>
> To: "Alberg 30 public list" <public-list at alberg30.org>
> Subject: Re: [Alberg30] Genoa Travler
> Date: Tue, 25 Nov 2003 16:59:24 -0500
>
> Larry;
>
> Thanks for your "if it ain't broke don't fix it" vote. I will do the
count
> when the polls close.
>
> The fact that I have gotten other inquiries like yours below regarding my
> docking technique leads me to wonder if I could better occupy everyone's
> time discussing docking, not toe rails. I have always thought that one
> should hit the dock at an angle of about 30 degrees and only hard enough
to
> have the forward end of the boat bounce out enough so the boat drifts
> parallel to the dock. If you go too fast the bow will bounce too far away
> from the dock (which is only a problem if you can' get a bow line over the
> piling) and the impact will not be enough to stop the forward momentum of
> the boat (which is only a problem if there is another boat, dingy, Manatee
> and/or a lousy, rotten dock that can't even take the impact of a little
> sailboat without collapsing right in front of your eyes... in the way).
> Perhaps there is a better way I am missing.
>
> Roger
> Old, beat up, toe rail-less #148
>
> ----- Original Message -----
> From: "Larry Morris" <larmor at myexcel.com>
> To: "'Alberg 30 public list'" <public-list at alberg30.org>
> Sent: Monday, November 24, 2003 1:06 PM
> Subject: RE: [Alberg30] Genoa Traveler
>
>
> > I vote for the ain't broke don't fix it solution. By the way, how hard
> > do you hit your dock anyway? I think if you hit a piling hard enough
to
> > dislodge the genoa track or egg shape the bolt holes, you will have
> > bigger problems to deal with.
> >
> >
> > Larry Morris
> > Solstice #501
> >
> >
> > -----Original Message-----
> > From: public-list-bounces at alberg30.org
> > [mailto:public-list-bounces at alberg30.org] On Behalf Of Roger L.
> > Kingsland
> > Sent: Sunday, November 23, 2003 3:42 PM
> > To: dk.campbell at sympatico.ca; Alberg 30 public list
> > Subject: Re: [Alberg30] Genoa Travler
> >
> > Don;
> >
> > To answer your question ("Why would you want to try to weaken the
> > attachment point for wind and genoa forces on an AL 30?"), first the
> > short
> > answer followed by the long answer (for the insomniac Albergers) that I
> > composed some time ago to sort out the issues for myself. Any feedback
> > would be appreciated.
> >
> > Short Answer:
> > I am sure the "if it ain't broke, don't fix it" crowd will point out
the
> > thousands of Albergs and other boats of the era having a similar toe
> > rail
> > detail that haven't sunk yet. But, this detail simply does not stand
up
> > to
> > the logic test and, in my humble, newbie opinion, it is definitely
> > broke.
> > The problem is the fastening system requiring great strength and
> > rigidity
> > (the structural connection between hull and deck) is the wrong type
> > (shear
> > vs. friction) and is constantly subjected to forces that weaken it
> > (bumps
> > into the dock and genoa sheet loads).
> >
> > To me, the solution is to create a good, bonded friction connection
> > between
> > hull and deck and to separate connections for the loads on the toe rail
> > and
> > genoa track. Thus the question about moving the traveler inboard.
> > Also,
> > the wind load on a 400 square foot sail at 30 knots is under 2,000
> > pounds
> > (assuming the sail is still intact in such wind), half of which goes to
> > the
> > sheet. If the sheet enters the block at 45 degrees, the upward force
on
> > the
> > track is less than 800 pounds (500 pounds at 30 degrees). It is
> > relatively
> > easy to distribute with the proper backer plate.
> >
> > Long Answer:
> > I am in the process of replacing my toe rail on #148 and I have the
> > impression the rivets were meant primarily to hold the deck and hull
> > together during chemical bonding. The rivets, which I drilled out and
> > filled with Marine Tex were too small and too deteriorated to have any
> > appreciable tensile or shear strength and were located near the outside
> > edge
> > of the joint overlap where they would not be effective in creating a
> > friction connection (but would do a good job of holding the hull and
> > deck
> > together
> > while the joint cured). I replaced them with 3/16" SS rivets 4" OC
> > about
> > 1-1/2" inboard (my hand still hurts).
> >
> > The thru bolted toe rail fasteners (3/16" SS bolts, 6" OC) seem to be
> > the
> > primary hull/deck mechanical fastener. The problem with these is,
> > because
> > they also hold the toe rail, they can not be tightened sufficiently
(the
> > teak doesn't have sufficient compressive strength) to create a friction
> > connection (like that created by a clamp or Chinese handcuffs) at the
> > intersection of hull and deck. If the chemical bond fails, the only
> > remaining bond is the aluminum rivets (which are marginal) and the
shear
> > connection created where the SS bolts that pass thru the hull/deck
> > material.
> >
> > A shear connection is only as strong as the surface area that "pushes"
> > against the sides of the connector; in this case, the sides of the
holes
> > in
> > the hull and deck (each less than 1/2" thick) forced against the bolt
> > shaft.
> > Also, unless there are no gaps between the fastener and the
> > material being fastened, the shear connection comes into play only
after
> > the
> > chemical bond fails. So instead of the mechanical fastener adding to
> > the
> > strength of the chemical bond, its strength is only realized after the
> > chemical bond
> > fails. I suspect the chemical bond is stronger so, if a force
> > sufficient
> > to break that bond is applied, a second application of the same force
> > would
> > also cause failure of the mechanical fasteners. Glug, glug.
> >
> > Ensuring bolt holes are filled with epoxy (often a messy, hit-or-miss
> > process) or using fully threaded screws would allow both connections to
> > work
> > in
> > concert but, the limited strength of a mechanical fastener in shear
> > would
> > still be a problem. A screw with a smooth shaft at the upper of the
two
> > layers being fastened will create a friction connection but its
strength
> > will be limited the thread grip on the relatively thin lower material.
> >
> > The dual function of the fasteners creates another problem. That is
the
> > fasteners that hold the hull and deck together also hold the toe rail
> > (AKA,
> > bumper) onto the deck. Just a minor bump against a piling can
> > cause movement of the bolts which will enlarge the hole through which
> > the
> > bolt
> > passes (I removed bolts forward that had a lazy "S" shape). In
> > addition,
> > any eccentric load on the genoa traveler attached to the top of the
rail
> > will "work' the thru deck bolts. Close hauled, where loads are higher
> > and
> > more longitudinal, the depth of the toe rail will create shear
> > resistance.
> > When loads are transverse, as in when the sail is out (especially when
> > held
> > out by a whisker pole), the thin toe rail does little to prevent
bending
> > in
> > the bolts which are essentially cantilevered from the deck. I suspect
> > this
> > is why we read postings such as this one from George Dinwiddie, "Most
of
> > my
> > leaks in the lockers under the salon windows have come from leaking
> > genoa
> > track bolts." The result is water tight integrity becomes entirely
> > dependant on the bedding compound (which can also be effected by
> > movement in
> > the toe rail) and the sheer connection no longer works in concert with
> > the
> > chemical bond (per above).
> >
> >
> >
> >
> > Roger Kingsland
> > Chief Financial Officer (AKA, check writer)
> > Mahina Manu, A30 #148
> > N40° 29.288'
> > W79° 54.228'
> >
> > Author's Disclaimer; This email was produced exclusively by the sender
> > and,
> > in the interest of expediency, without the benefit of editing by
others.
> > The sender, thank goodness, is a much better architect/sailor than
> > speller/editor and, frankly, constantly laments an obvious flaw in
> > "spell
> > check," it does not know what the author is thinking. Please accept
the
> > sender's sincere apologies for any "typos" that may appear in this
> > document.
> > If present, they are certainly unintended and hopefully do not cloud
the
> > message, or spawn any unnecessary lawsuits.
> >
> > ----- Original Message -----
> > From: "Don Campbell" <dk.campbell at sympatico.ca>
> > To: "Alberg 30 public list" <public-list at alberg30.org>
> > Sent: Sunday, November 23, 2003 11:44 AM
> > Subject: Re: [Alberg30] Genoa Travler
> >
> >
> > > The WTC fell when it went out of column and the support was too weak
> > to
> > hold the weight due to gravititational forces of the mass. Why would
you
> > want to try to weaken the attachment
> > > point for wind and genoa forces on an AL 30?
> > >
> > > "Roger L. Kingsland" wrote:
> > >
> > > > I have considered moving my genoa traveler inboard about 2" so I
> > could
> > attach it directly to the deck instead of the toe rail. Would this be
> > permitted under the class racing rules?
> > > >
> > > > Roger L. Kingsland, AIA
> > > > Managing Partner
> > > > Kingsland Scott Bauer Associates (KSBA)
> > > > N40° 27' 49" W79° 57' 59"
> > > > 3441 Butler Street
> > > > Pittsburgh, PA 15201
> > > > www.ksba.com
> > > >
> > > > 1(412) 252-1500 X101 - Office & Voice Mail
> > > > 1(412) 779-5101 - Mobile (no voice mail)
> > > > 1(412) 252-1510 - Fax
> > > >
> > > > +---------------------------------------------------------------+
> > > > | This Old Boat by Don Casey |
> > > > | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
> > > > +---------------------------------------------------------------+
> > > >
> > > > Public-list mailing list -- Public-list at alberg30.org
> > > > http://www.alberg30.org/mailman/listinfo/public-list
> > > > To unsubscribe: email to Public-list-request at alberg30.org
> > > > Include command "unsubscribe <password>" in subject or body.
> > > > Use command "help" for more options.
> > >
> > > +---------------------------------------------------------------+
> > > | This Old Boat by Don Casey |
> > > | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
> > > +---------------------------------------------------------------+
> > >
> > > Public-list mailing list -- Public-list at alberg30.org
> > > http://www.alberg30.org/mailman/listinfo/public-list
> > > To unsubscribe: email to Public-list-request at alberg30.org
> > > Include command "unsubscribe <password>" in subject or body.
> > > Use command "help" for more options.
> > >
> > >
> >
> >
> > +---------------------------------------------------------------+
> > | This Old Boat by Don Casey |
> > | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
> > +---------------------------------------------------------------+
> >
> > Public-list mailing list -- Public-list at alberg30.org
> > http://www.alberg30.org/mailman/listinfo/public-list
> > To unsubscribe: email to Public-list-request at alberg30.org
> > Include command "unsubscribe <password>" in subject or body.
> > Use command "help" for more options.
> >
> >
> > +---------------------------------------------------------------+
> > | This Old Boat by Don Casey |
> > | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
> > +---------------------------------------------------------------+
> >
> > Public-list mailing list -- Public-list at alberg30.org
> > http://www.alberg30.org/mailman/listinfo/public-list
> > To unsubscribe: email to Public-list-request at alberg30.org
> > Include command "unsubscribe <password>" in subject or body.
> > Use command "help" for more options.
> >
> >
>
>
> +---------------------------------------------------------------+
> | This Old Boat by Don Casey |
> | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
> +---------------------------------------------------------------+
>
> Public-list mailing list -- Public-list at alberg30.org
> http://www.alberg30.org/mailman/listinfo/public-list
> To unsubscribe: email to Public-list-request at alberg30.org
> Include command "unsubscribe <password>" in subject or body.
> Use command "help" for more options.
>
> _________________________________________________________________
> >From the hottest toys to tips on keeping fit this winter, you'll find a
> range of helpful holiday info here.
> http://special.msn.com/network/happyholidays.armx
>
> +---------------------------------------------------------------+
> | This Old Boat by Don Casey |
> | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
> +---------------------------------------------------------------+
>
> Public-list mailing list -- Public-list at alberg30.org
> http://www.alberg30.org/mailman/listinfo/public-list
> To unsubscribe: email to Public-list-request at alberg30.org
> Include command "unsubscribe <password>" in subject or body.
> Use command "help" for more options.
>
>
+---------------------------------------------------------------+
| This Old Boat by Don Casey |
| http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
+---------------------------------------------------------------+
Public-list mailing list -- Public-list at alberg30.org
http://www.alberg30.org/mailman/listinfo/public-list
To unsubscribe: email to Public-list-request at alberg30.org
Include command "unsubscribe <password>" in subject or body.
Use command "help" for more options.
+---------------------------------------------------------------+
| This Old Boat by Don Casey |
| http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
+---------------------------------------------------------------+
Public-list mailing list -- Public-list at alberg30.org
http://www.alberg30.org/mailman/listinfo/public-list
To unsubscribe: email to Public-list-request at alberg30.org
Include command "unsubscribe <password>" in subject or body.
Use command "help" for more options.
1069952811.0
More information about the Public-List
mailing list