[Public-list] RE: Head Holding tank

[Mike Lehman]

Maybe they cahnged some things since I did mine - now it looks like the 5057 
is the right one. I am doing this from memory , but it seems to the the 
height was 16" not 19" as shown in the 5022. I will take some more 
measurements and let you know. I also, strongly advize that befor buying any 
tank , that you make careful measurents of your boat since we have found 
some differences from one boat to another.



              Mike Lehman
><((((º>¸.·´¯`·...¸><((((º>





----Original Message Follows----
From: "Chris Lawrence" <chris.lawrence at sympatico.ca>
Reply-To: Alberg 30 Public List -- open to all <public-list at alberg30.org>
To: "'Alberg 30 Public List -- open to all'" <public-list at alberg30.org>
Subject: RE: [Public-list] RE: Head Holding tank
Date: Sun, 5 Sep 2004 23:41:23 -0400


Mike
I looked at the Kracor website and Mold 5022 shown in your drawing is listed
as having 17 gallons, not 15. So either Kracor has increased the capacity of
the mold by using thiner materials (the outside dimensions are the same as
in your drawing), or you have 2 more gallons of capacity with which to
surmount unforseen circumstances...see link below


http://www.kracor.com/support/holdingtanks.pdf


Chris Lawrence

Cirrus #500

24 Scarborough Road
Toronto, Canada M4E 3M5
T: 416-698-5136 F: 416-698-8953 E: chris.lawrence at sympatico.ca


-----Original Message-----
From: public-list-bounces at alberg30.org
[mailto:public-list-bounces at alberg30.org] On Behalf Of Chris Lawrence
Sent: 25 August 2004 18:43
To: 'Alberg 30 Public List -- open to all'
Subject: [Public-list] RE: Head Holding tank


Thanks Mike - this helps a lot - your install looks A1!
The tank I have is in the undersole, and I believe it was factory installed.
The previous owner had glassed over the entire surface and subsequently
caulked all around it; however it leaks and is now beyond repair. I think an
install in the forward berth makes more sense, because it is always better
to be able to see the bilges and I am thinking I will try and copy what you
have done.

Thanks again and best regards

Cirrus #500

Chris Lawrence
24 Scarborough Road
Toronto, Canada M4E 3M5
T: 416-698-5136 F: 416-698-8953 E: chris.lawrence at sympatico.ca


-----Original Message-----
From: public-list-bounces at alberg30.org
[mailto:public-list-bounces at alberg30.org] On Behalf Of Mike Lehman
Sent: 25 August 2004 11:38
To: public-list at alberg30.org
Subject: RE: [Public-list] where is #277?


My boat is hull #505 and I installed a Kracor 14 gallon tank under the
v-berth on the portside, just in front of the bulkhead. Did your boat have a

factory installed tank, or is the present tank from a previous owner? My
boat did not have a tank. To see some pictures of the installation go to:

http://alberg30.org/maintenance/disorganized/head/

Hope this helps.



               Mike Lehman
 ><((((º>¸.·´¯`·...¸><((((º>





----Original Message Follows----
From: "Chris Lawrence" <chris.lawrence at sympatico.ca>
Reply-To: Alberg 30 Public List -- open to all <public-list at alberg30.org>
To: "'Alberg 30 Public List -- open to all'" <public-list at alberg30.org>
Subject: RE: [Public-list] where is #277?
Date: Wed, 25 Aug 2004 11:04:33 -0400

Has anyone replaced a waste holding tank recently and if so any tips and
what did you replace with? Thanks

Cirrus #500

Chris Lawrence
24 Scarborough Road
Toronto, Canada M4E 3M5
T: 416-698-5136 F: 416-698-8953 E: chris.lawrence at sympatico.ca

_______________________________________________
Public-list mailing list
Public-list at alberg30.org
http://alberg30.org/mailman/listinfo/public-list



 1094561726.0