[Public-list] Original gatevalve sizes

[Jack Vanderloo]

Gord,

I'm 'round the corner in Penetang - Dutchman's Cove. No slip; winter 
there, then cruise 2-3 months full time.

Would that commercial plumbing supplier be St. Amant's, by any chance?

Will be down on April 20/21 to drop off new cushions and other bulky 
items before swinging down to Guelph to pick up my daughter from 
university.  Back in mid-May for much needed project work (and noted 
survey) and launch mid-June.  Superior, to Thunder Bay, is in the plans. 
  (Tested Whitefish Bay last year.)

Back on topic, could one mate a bronze thru-hull with a brass ball-valve 
with some semblance of expectations of safety/durability?

Cheers
Jack


Gordon Laco wrote:

> Hello Jack -
> 
> I am with Eclisiastical and Larry Fraser is my broker.  I was with Robertson
> & Robertson years ago  in my wooden boat days but found a better deal
> through a diff broker.
> 
> I have not yet settled on a surveyor - I forget where you are.  I am in
> Midland on Georgian Bay.
> 
> Gord
> 
> 
> 
> 
> 
> 
> 
>>Thanks for taking the time to do this, Gord - what with being upside
>>down, in wet snow and all!
>>
>>The irony is that I'm doing the same job for the same reason.  You
>>perchance also with Robertson & Robertson?  Must have mass-mailed the
>>call for updated surveys.  (BTW, am I correct in assuming the survey is
>>yet to be done?  Who are you lining up?  Perhaps we can get a twofer, or
>>some such deal.)
>>
>>Where did you source your ball-valves, thru-hulls, locking rings and/or
>>nipples?  And, were you concerned about the bronze/brass issue?
>>
>>I did some research in the alberg30.org archives and noted that Taylor
>>Echlin (#612) had also gone through the experience recently ... with
>>some interesting observations on the re-use of thru-hulls, backing
>>plates and locking rings.
>>http://www.alberg30.org/pipermail/public-list/2004-June/000531.html
>>
>>Jack
>>Aldabi KC641
>>
>>Gordon Laco wrote:
>>
>>
>>>Hi Jack - 
>>>
>>>I am in the middle of that job now.  I got a note from my marine insurer
>>>that this year I need a survey so decided to bite the bullet and change over
>>>from gate valves to ball valves.  Fairly horrible miserable job esp the
>>>cockpit drains and the scupper hoses... Besides the little flim flam with
>>>the changing diameter, we found that the ball cocks are taller than the gate
>>>valves.  What that meant was cutting the longitudinal bulkhead to allow the
>>>scupper hoses to come in at the right angle.  Then came the ordeal of trying
>>>to push the hoses onto the new hose barbs while upside down in the cockpit
>>>lockers, with wet snow falling on us.. Etc etc
>>>
>>>But, the job had to be done.
>>>
>>>Here is what was in my #426:
>>>
>>>Engine cooling intake - 1/2"
>>>
>>>Cockpit drains - 1" through hulls, but 1 1/4" hoses (did you hear cursing
>>>coming from the north the day I discovered that?)
>>>
>>>Sink intake - was 3/8", I changed it to 1/2" (that one was one of those
>>>'fake' through hulls Whitby used and I changed it)
>>>
>>>Sink drain - 1" and I kept to that size
>>>
>>>Head intake - was 3/8" and we went to 1/2"
>>>
>>>Head overboard... Being a Great Lakes boat we don't have one of those.
>>>
>>>Cheers - Gord #426 Suprise
>>>
>>>
>>>
>>>
>>>
>>>>Has anyone gone through a recent gate-valve to ball-valve/seacock
>>>>conversion, i.e., from the original gate-valves on a liner-vintage A30
>>>>(1977, 1978)?
>>>>
>>>>My boat is about 500km/300mi from home, so I'd like to document the
>>>>existing arrangement for planning/costing purposes while the water is
>>>>still hard.
>>>>
>>>>Aside from the engine discharge, what are the nominal sizes of the
>>>>following original GATE-valves:
>>>>Cockpit/deck drains
>>>>Engine cooling intake
>>>>Sink intake
>>>>Sink discharge
>>>>Heads intake
>>>>Heads overboard discharge
>>>>
>>>>Thanks
>>>>
>>>>Jack
>>>>Aldabi KC641
>>>>
>>>>
>>>>_______________________________________________
>>>>Public-list mailing list
>>>>Public-list at alberg30.org
>>>>http://alberg30.org/mailman/listinfo/public-list
>>>
>>>
>>>_______________________________________________
>>>Public-list mailing list
>>>Public-list at alberg30.org
>>>http://alberg30.org/mailman/listinfo/public-list
>>>
>>>
>>
>>_______________________________________________
>>Public-list mailing list
>>Public-list at alberg30.org
>>http://alberg30.org/mailman/listinfo/public-list
> 
> 
> _______________________________________________
> Public-list mailing list
> Public-list at alberg30.org
> http://alberg30.org/mailman/listinfo/public-list
> 
> 


 1112563714.0