[Public-list] Stanchion Question

[Dave Terrell]

when you got the tubing from on-line, how did make openings for the life
line in the tubing? the hole in the top .29 inches woudl be too small
for my lifelines which are 5/16 (I think). If they were 1/4 they would
slide through the hole on top with room to spare. Am I on the right
track or missing something?

>>> sousa_stephen at emc.com 01/05/06 3:41 PM >>>
That cap with an allen screw has the fitting for the life line. Also
you can
always give them a call. 

-----Original Message-----
From: public-list-bounces at alberg30.org 
[mailto:public-list-bounces at alberg30.org] On Behalf Of Dave Terrell
Sent: Thursday, January 05, 2006 3:31 PM
To: public-list at alberg30.org 
Subject: RE: [Public-list] Stanchion Question

How did you get openings for the life line? I did not find a screw-on
top at suncor. I did find a top cap that would attach with an allen
screw. could that be it?  Thanks

>>> sousa_stephen at emc.com 01/05/06 8:04 AM >>>
Dave,

Suncor has a base that matches (very close)to the Alberg. I used there
base
and tops which are screw on and ordered the stainless tubing which is
.060
from Online Metals.Com. they cut the material to 24 inches you just
put
them
together.

Stephen


Original Message-----
From: public-list-bounces at alberg30.org 
[mailto:public-list-bounces at alberg30.org] On Behalf Of Dave Terrell
Sent: Wednesday, January 04, 2006 9:40 PM
To: public-list at alberg30.org 
Subject: Re: [Public-list] Stanchion Question

Garhauer has 24 " stainless tubes - one lifeline - for $27 and loose
change. Tops-in-Quality has them for $44. $48 for two lifelines.
Top-in
quality will duplicate the base for $52/base. Their standard base does
not match our bolt pattern - or least my pattern.

>>> gdinwiddie at alberg30.org 01/04/06 7:33 PM >>>
FINNUS505 at aol.com wrote:
> Has anyone replaced individual stantions that were bent? Is there an


> affordable source for stantions that match the originals?

I have.  I just used some stainless tubing (and reused the lifeline 
guide at the top).  Note that some of the stanchions are supposed to
be

bent in slightly just above the base.  This lets them stand up
straight

on a sloped deck, rather than leaning outboard.

_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html 
Please support them.
_______________________________________________
Public-list mailing list
Public-list at alberg30.org 
http://alberg30.org/mailman/listinfo/public-list 

_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html 
Please support them.
_______________________________________________
Public-list mailing list
Public-list at alberg30.org 
http://alberg30.org/mailman/listinfo/public-list 
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html 
Please support them.
_______________________________________________
Public-list mailing list
Public-list at alberg30.org 
http://alberg30.org/mailman/listinfo/public-list 
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html 
Please support them.
_______________________________________________
Public-list mailing list
Public-list at alberg30.org 
http://alberg30.org/mailman/listinfo/public-list 
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html 
Please support them.
_______________________________________________
Public-list mailing list
Public-list at alberg30.org 
http://alberg30.org/mailman/listinfo/public-list

 1136494174.0