[Public-list] Public-list Digest, Vol 693, Issue 1

[Jonathan Adams]

Mine come back to a turning block. I actually have two - you can see them http://mysite.verizon.net/vze2s2y6/id1.html The guy that had the boat before me was into them. Mine are actually bolted to the rail and into the deck. I have not seen them flex.
 
My winches may be further forward than yours. This arrangement would not work so well if I was using the aft winch.
 
JA
Laughing Gull 197

----- Original Message ----
From: J Bergquist <jbergqui at gmail.com>
To: Alberg 30 Public List -- open to all <public-list at alberg30.org>
Sent: Tuesday, June 6, 2006 1:09:43 PM
Subject: Re: [Public-list] Public-list Digest, Vol 693, Issue 1


Tim Williams uses turning blocks on LinGin. You might ask him about them. I
think that they blew one up in the 2002 NOOD. It was windy that day. Those
blocks are under a lot of load, as you pointed out.

Personally, I like them because I think they make a good lead into the
winch.

I would look at LinGin if I were you, and ask Tim why he uses them.

J

On 6/6/06, Mike Lehman <sail_505 at hotmail.com> wrote:
>
> Mine leads from the genoa car directly to the winch. I move the car
> forward
> and backward depending on the size of the headsail and wind conditions. In
> all of my years, I think I may have seen one other Alberg with a double
> block arrangement for the genoa sheets.
>
>
>
> Mike Lehman
> ~~~_/)_/)~~_/)~~~
>
>
>
>
> ----Original Message Follows----
> From: "Cole, Andrew L" <andrew.cole at llff.com>
> Reply-To: Alberg 30 Public List -- open to all <public-list at alberg30.org>
> To: <public-list at alberg30.org>
> Subject: Re: [Public-list] Public-list Digest, Vol 693, Issue 1
> Date: Tue, 6 Jun 2006 12:22:41 -0400
>
> This is the way we led it originally, but it seemed to bind the car
> somewhat with the side loading to get aft to the primary.  The car is a
> more modern ball bearing car with the sheave integrated into the car
> with limited range of motion.
>
> I will take a look again tomorrow night with the sheet coming directly
> off the car.
>
> Does anyone use a turning block for the genoa sheet or am I the only
> black sheep?
>
> Andrew
>
> >Dear Andrew,
> >I don't think that you need to run your sheets through
> >the second car. You should be able to go directly from the first car to
> the
> >winch. The sideways stress is practically removed , the strain then
> being
> >upwards at the car location which would seem to be acceptable. Jonathan
>
> Cole, Andrew L
> Admitted in Maryland, Virginia & Florida
> One Corporate Center
> 10451 Mill Run Circle, Suite 1000
> Baltimore MD 21117
>
>
> tel: 410 581-7408
> fax: (410) 581-7410
> mob: (410) 206-3577
>
> --------------------------------------------------------
> This message contains confidential information and is intended only for
> public-list at alberg30.org. If you are not public-list at alberg30.org you
> should
> not disseminate, distribute or copy this e-mail. Please notify
> andrew.cole at llff.com immediately by e-mail if you have received this
> e-mail
> by mistake and delete this e-mail from your system. E-mail transmission
> cannot be guaranteed to be secure or error-free as information could be
> intercepted, corrupted, lost, destroyed, arrive late or incomplete, or
> contain viruses. Cole, Andrew L therefore does not accept liability for
> any
> errors or omissions in the contents of this message, which arise as a
> result
> of e-mail transmission. If verification is required please request a
> hard-copy version.
> --------------------------------------------------------
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-list mailing list
> Public-list at alberg30.org
> http://alberg30.org/mailman/listinfo/public-list
>
> _________________________________________________________________
> Express yourself instantly with MSN Messenger! Download today - it's FREE!
> http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-list mailing list
> Public-list at alberg30.org
> http://alberg30.org/mailman/listinfo/public-list
>
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-list mailing list
Public-list at alberg30.org
http://alberg30.org/mailman/listinfo/public-list
 1149615328.0