[Public-List] Partial Taffrail Replacement on Non-Liner Boat

[Jonathan Budington]

My taffrail needs replacement as well.  I'm curious about Michael's post
"the top board of the taffrail" - could I replace the top board without
removing the bottom board?  I assumed they were glued together.
Replacing only the top board (the damaged piece on my boat) would be a
less daunting project.

Jon

-----Original Message-----
From: public-list-bounces at lists.alberg30.org
[mailto:public-list-bounces at lists.alberg30.org] On Behalf Of Michael
Connolly
Sent: Tuesday, February 05, 2008 10:49 AM
To: Alberg 30 Public List -- open to all
Subject: Re: [Public-List] Partial Taffrail Replacement on Non-Liner
Boat

Andrew,
   
  The top board of the taffrail on Lorrie Rose # 133 is also badly
damaged.  For a while the earlier boats had what I call a "ventilated"
taffrail.   My meaning is that water could flow thru it to get off the
stern.  The upper board was positioned on 5 or 6 "piers" which allowed
water to pass between them and off the stern.  I always thought that
this was a better design, although easier to break if you jumped on the
top board between the piers. It might be a thin bottom board then the
piers and then a thicker top board.  Others on this list can comment as
to the specifics.
   
  From what I remember of my taffrail, none of the three boards are
bent.  They are all cut in the curve from flat boards.  Inspect closely
the grain and you will see that this is the case.  Use a band saw and
cut yourself a new top board, actually several boards.  Each layer of
the three is made up of several boards cut so that their joints overlap.
When glued together they overlap enough to stay
together.................at least for 25 or so years.  Or in my case 42
years.
   
  Michael

"Cole, Andrew L" <andrew.cole at llff.com> wrote:
  I am in the middle of replacing the top layer of the taffrail (stern
rail) on Andante. The taffrail appears to have originally been
constructed of three laminated layers of 3/4 inch teak. The top of the
three layers on our boat needs replacing (the bottom two are
serviceable). Has anyone done this replacement? Any thoughts on
bending the teak? Bending the 3/4 to the curve is difficult, there has
to be a better way... Does anyone in the Annapolis area have a template
for the replacement?

I can probably plane the 3/4 down to 5/8 or 1/2 and still match the
height of the toerail on either side (I was going to have to shave the
ends down otherwise). That reduction in thickness may make the bending
easier, but the project is still somewhat daunting.

Any suggestions are welcome.

Thanks,

Andrew
Andants - 152 

Cole, Andrew L
Admitted in Maryland, Virginia & Florida
One Corporate Center
10451 Mill Run Circle, Suite 1000
Baltimore MD 21117


tel: 410 581-7408
fax: (410) 581-7410
mob: (410) 206-3577

--------------------------------------------------------
This message contains confidential information and is intended only for
public-list at lists.alberg30.org. If you are not
public-list at lists.alberg30.org you should not disseminate, distribute or
copy this e-mail. Please notify andrew.cole at llff.com immediately by
e-mail if you have received this e-mail by mistake and delete this
e-mail from your system. E-mail transmission cannot be guaranteed to be
secure or error-free as information could be intercepted, corrupted,
lost, destroyed, arrive late or incomplete, or contain viruses. Cole,
Andrew L therefore does not accept liability for any errors or omissions
in the contents of this message, which arise as a result of e-mail
transmission. If verification is required please request a hard-copy
version.
--------------------------------------------------------
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

 1202230764.0