[Public-List] Stripping Bottom Paint - Any Experience with Soy/Chemical Strippers?

[Roger L. Kingsland]

Hi all Albergers,

I have had some success placing a 20" house fan 4' to 6' "upwind" of the
sanding.  It does a pretty good job of clearing the sander exhaust before
too much makes it to the respirator.  Of course, it would be good not to
have other boats too close downwind.  I have also jury rigged a shop vac
nozzle to the sander w/ duct tape but it's hard to get it in a place where
it will collect everything, comes off easily (even if you use an entire roll
of duct tape) and it takes half a day to clean the vacuume.

For a more extreme approach, at one time I kept good old #148 at a friend's
factory that had not one but two 20 ton bridge cranes.  I thought it would
be easier to sand the bottom w/ the boat on its side.  So, I bought a 3' x
6' air pillow ("dunnage bag" used to hold truck cargo in place) with the
intention of using the crane to put the keel on the concrete factory floor
and rolling the boat on it's side (I suppose one just pushes the boat
amidships once the crane straps get a little slack) and resting it on the
pillow.  Imagine, access to the bottom of the keel, no sanding above your
head, no boat stands/pads to work around; do one side, roll her over, then
do the other.

Anyway, perhaps its a good thing my friend sold the business and I got
kicked out before I could give it a try.  Anyone need a dunnage bag?  Still
in the box.       

Roger 148


-----Original Message-----
From: public-list-bounces at lists.alberg30.org
[mailto:public-list-bounces at lists.alberg30.org] On Behalf Of C.B. Currier
Sent: Sunday, July 20, 2008 9:53 AM
To: Alberg 30 Public List -- open to all
Subject: Re: [Public-List] Stripping Bottom Paint - Any Experience with
Soy/Chemical Strippers?


   Yeah !
   I did it from February to March in '04 ... not hot but lots of work &
   it took half the boat for me to realize that the 24 grit stuff really
   made the difference. I started with 80 then gradually worked my way
   down. Arrrgh!
   Anyway, once you are done you will have a beautiful hull! I know I am
   STILL proud of the work I did!
   Oh and your hands will probably vibrate for a week :>
   C.B.
   [1]laserandy at aol.com wrote:

CB,

I took your advice.  That is definitely the 'manly' way to remove bottom
paint.
  After several hours of work,
a partially failed resperator (boy do I have a headache), and a slightly
worse for the wear Dewalt, I've got about half the boat stripped.  By the
time I finished I could no longe r breathe through the resperator and
probably sucked CO2 for most of last part.

I feel like shaving my head, scrubbing the rest of my body with a pummice
stone , and going to sleep.
My hands are still vibrating.

I'll be back at it again tomorrow with a new resperator and some more 'rocks
on  paper'

Andrew



I strongly advocate sanding! Use a RO sander with 24 grit (floor sanding
paper). It is practically rocks glued to paper ...
paint comes off really easily.
C.B. Currier
Infinity #57
Daybreak #458


_______________________________________________
These businesses support your Association:
[2]http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
[3]Public-List at lists.alberg30.org
[4]http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

References

   1. mailto:laserandy at aol.com
   2. http://www.alberg30.org/store/A30supporters.html
   3. mailto:Public-List at lists.alberg30.org
   4. http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org


 1216652420.0