[Public-List] Tiller Head

edward schroeder eddiediver at sbcglobal.net
Sun Oct 11 18:51:35 PDT 2009


No problem getting the head off; I drilled the hole all the way thru after i got the replacement head on the rudder post centered.

--- On Sun, 10/11/09, Jonathan Budington <jon at globalprinting.com> wrote:


From: Jonathan Budington <jon at globalprinting.com>
Subject: Re: [Public-List] Tiller Head
To: "Alberg 30 Public List -- open to all" <public-list at lists.alberg30.org>
Date: Sunday, October 11, 2009, 9:50 AM


Ed,

This sounds like my problem  Did you have any trouble getting the head off after the key slipped?  Any advice on drilling that hole?  Sounds like a permanent fix.

Thanks,

Jon

-----Original Message-----
From: public-list-bounces at lists.alberg30.org [mailto:public-list-bounces at lists.alberg30.org] On Behalf Of edward schroeder
Sent: Sunday, October 11, 2009 10:26 AM
To: Alberg 30 Public List -- open to all
Subject: Re: [Public-List] Tiller Head

On Emotional Rescue #303, I replaced the tiller head as it was also slipping. I discovered that the bronze key was not engaged sufficiently, or had abraded from a once-sufficient size, so that it did not engage the groove to take the shearing force.Also, the clamp on the aft side of the head did not grip sufficiently. 
 
However, when I purchased a new head from Edson, it too had the groove cut, not on center, so that it forced the tiller to be off-center. I sent two back to Edson before I received a straight head. Edson told me that they were cutting the grooves by hand and that "some could be slighly crooked". I was disappointed with there answer.
 
I subsequently drilled a hole athwartship through the entire head and rudder post and inserted a 1/8 inch bolt and nut to take the shear force. Since then (5 years) we have had no trouble.
 
Ed Schroeder
 
--- On Sun, 10/11/09, Jonathan Budington <jon at globalprinting.com> wrote:


From: Jonathan Budington <jon at globalprinting.com>
Subject: [Public-List] Tiller Head
To: "Alberg 30 Public List -- open to all" <public-list at lists.alberg30.org>
Date: Sunday, October 11, 2009, 8:18 AM


I was sailing last night - beautiful evening with about 12 knots of
breeze.  We passed under the Bay Bridge, and we were hit by a 25 knot
gust.  The boat wanted to head up, so I pushed down hard on the tiller.
We reduced sail, but I noticed I was fighting to keep the boat on track.
I realized that the to keep the boat on a straight course, I had to keep
the tiller almost all the way over to the starboard side.  I made it
back to Annapolis, but the last left turn into the slip was a real
challenge.  I played with the tiller after we tied up; it seems to be in
full control of the rudder, but way off center.  Could the head have
slipped on the post?  Doesn't the post have a keyway to prevent this?
Could it be something worse? 

Jon Budington

_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

 1255312295.0


More information about the Public-List mailing list