[Public-List] block sized

Fri Jun 3 08:17:12 PDT 2011

Roger, 

I misunderstood you. When you were referring to the tapered edge you were referencing the plan view of the spreader.  I assumed that you were referencing the crossectional view of the spreader!!  So from my point of view the blunt edge (non-tapered)  of the 1-1/8" cross section faces forward, and from your point of view the tapered edge on the plan view faces forward. All confused please raise your hands. 

Michael 

----- Original Message ----- 
From: "Roger L. Kingsland" <r.kingsland at ksba.com> 
To: "Alberg 30 Public List -- open to all" <public-list at lists.alberg30.org> 
Sent: Tuesday, May 31, 2011 4:13:22 PM 
Subject: Re: [Public-List] block sized 

With my old wood spreaders, it appears the tapered edge slopes aft while the 
vertical edge runs athwart ships; so, putting the tapered edge forward, 
results in the stays about even w/ the back of the mast.  Hope it's FAST. 

Has anyone priced new aluminum (is carbon fiber class legal?)spreaders? 
Sure would be nice to get that extra few pounds off the mast. 

Best, Roger 148 

-----Original Message----- 
From: public-list-bounces at lists.alberg30.org 
[mailto:public-list-bounces at lists.alberg30.org] On Behalf Of C.B. Currier 
Sent: Tuesday, May 31, 2011 3:55 PM 
To: Alberg 30 Public List -- open to all 
Subject: Re: [Public-List] block sized 

I think the tapered edge is supposed to go forward, however, the 
spreaders by design were never supposed to sweep aft. 
I did that on my Boat, Infinity 7+ years ago and found she performed 
much better in big air, but no marked improvement in light air. 
It was pointed out to me that the spreaders were on backward, but we 
were winning so who cared. We got a bigger belly in the main as a result 
and did tighten up the slot some. But it does work against the natural 
run of the shrouds. 

C.B. Currier 
Infinity #57 (in Wellfleet Harbor, MA) 

On 05/31/2011 03:49 PM, crufone at comcast.net wrote: 
> 
> Roger, 
> 
> I suspect that the tapered edge goes aft. At any rate the spreaders after 
installed must be swept aft. 
> 
> Michael #133 
> ----- Original Message ----- 
> From: "Roger L. Kingsland" <r.kingsland at ksba.com> 
> To: "Alberg 30 Public List -- open to all" 
<public-list at lists.alberg30.org> 
> Sent: Tuesday, May 31, 2011 2:38:07 PM 
> Subject: [Public-List] block sized 
> 
> Hi Folks, 
> 
>   
> 
> Working on the mast; spreaders went on OK (the tapered side of the wood 
ones 
> goes forward, right?), need to replace topping lift and spinnaker halyard 
> blocks.  I have a couple of Harken bullet blocks with a 485 lb working 
load. 
> I assume one will be OK for the topping lift but wonder about the spin 
> halyard.  Any suggestions as to working load for the block? 
> 
>   
> 
> Thanks, 
> 
>   
> 
> Roger 
> 
>   
> 
>   
> 
>   
> 
> Roger Kingsland, Managing Partner 
> 
> Kingsland Scott Bauer Associates 
> 
>   
> 
> KSBA 
> 
>   _____   
> 
> Architects/Planners/InteriorDesigners/ProjectManagers 
> 
>   
> 
> 3441 Butler Street 
> 
> Pittsburgh, PA 15201 
> 
> N 40° 27.8344'  W79° 57.9831' 
> 
>   
> 
> 412-252-1500 ext.101 
> 
> 412-779-5101 cell 
> 
> 412-252-1510 fax 
> 
>  <blocked::blocked::mailto:r.kingsland at ksba.com> r.kingsland at ksba.com 
> 
>  <blocked::blocked::http://www.ksba.com/> www.ksba.com 
> 
>   
> 
>   
> 
> _______________________________________________ 
> These businesses support your Association: 
> http://www.alberg30.org/store/A30supporters.html 
> Please support them. 
> _______________________________________________ 
> Public-List mailing list 
> Public-List at lists.alberg30.org 
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 
> _______________________________________________ 
> These businesses support your Association: 
> http://www.alberg30.org/store/A30supporters.html 
> Please support them. 
> _______________________________________________ 
> Public-List mailing list 
> Public-List at lists.alberg30.org 
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 

_______________________________________________ 
These businesses support your Association: 
http://www.alberg30.org/store/A30supporters.html 
Please support them. 
_______________________________________________ 
Public-List mailing list 
Public-List at lists.alberg30.org 
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 

 1307114232.0