[Public-List] Rachel - Hull thickness question

[chris widing]

HI Sorry to highjack the tread. I just got a Alberg 30 #450 it needs alot of 
work and I have alot of learning to do about it. Was wondering about the 
tank you are ordering it is a holding tank ? Mine has one on the port side 
under the v berth.Looks like a complicated pump out and treatment system is 
it still leagal?  Lots of other ? that will follow. Thanks in advance chris
----- Original Message ----- 
From: <crufone at comcast.net>
To: "Alberg 30 Public List -- open to all" <public-list at lists.alberg30.org>
Sent: Wednesday, November 09, 2011 9:36 AM
Subject: Re: [Public-List] Rachel - Hull thickness question


>
>
> Richard,
>
> You could also try wooden blocking to shore the bracket against the outer 
> hull. It would be better to screw something into the new backet temporarly 
> rather than the hull.
>
> My two cents. BTW I guess the tank from Geroge worked out? Just placed the 
> group order for tanks yesterday, so you are about a month ahead of us.
>
> Michael #133
>
>
>
> ----- Original Message -----
>
>
> From: "Richard Hughes" <rjhughes at shaw.ca>
> To: "Alberg 30 Public List -- open to all" 
> <public-list at lists.alberg30.org>
> Sent: Tuesday, November 8, 2011 11:17:14 PM
> Subject: [Public-List] Rachel - Hull thickness question
>
> Installing a saddle tank in the stb locker to replace the tank under the
> cockpit sole.
> I have the tank, courtesy of another member of this site, but now need to
> install a "bracket" to secure it with, which I have fashioned out of epoxy
> coated wood. Now need to gently screw that bracket into the hull wall/side
> while west system sets up, then fibreglass over all.
>
> So, that's my tale, but running out of heat for fibregalss work!
>
> -----Original Message----- 
> From: Rachel
> Sent: Tuesday, November 08, 2011 7:50 PM
> To: Alberg 30 Public List -- open to all
> Subject: Re: [Public-List] Hull thickness question
>
> I can't speak to that exact spot, but I removed/replaced or filled all the
> below-the-waterline seacocks on the whole boat and the hull was around 
> 3/8"
> thick (and pretty uniform for all of them (#221).
>
> I'm trying to remember if I drilled or looked at any holes above the
> waterline... I don't think so, but if I remember any I will reply again.
>
> I'll admit that I'm curious why you are asking :) (But my mind just works
> that way - not that I'm challenging you or anything like that!)
>
> Rachel
> ex=#221
>
> On Nov 8, 2011, at 7:06 PM, Richard Hughes wrote:
>
>> Anyone know the thickness of the hull above the waterline, centre of stb
>> cockpit locker?
>> Installing new fuel tank.
>> Thanks Rick # 438
>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2012.0.1869 / Virus Database: 2092/4606 - Release Date: 11/09/11
> 


 1320855508.0