[Public-List] Shaft coupling detached
Don Campbell via Public-List
public-list at lists.alberg30.org
Sun May 31 18:18:45 PDT 2015
Check both ends of that coupling once you get the motor out. Look
particularly carefully, with a magnifying lens if necessary, at the keyway
because that area is prone to cracks, there is so little material
between the edge of the keyway and the outside of the coupling. If there
are cracks, be prepared to replace both ends of that coupling. Any set screw
on the coupling that fastens it to the shaft (motor or prop) will only
spread the crack open further.
Don
-----Original Message-----
From: Ramon Hildreth via Public-List
Sent: Sunday, May 31, 2015 1:00 AM
To: public-list at lists.alberg30.org ; public-list-request at lists.alberg30.org
Subject: [Public-List] Shaft coupling detached
Team,
Thanks for the help, by removing the electric panel and leaning over the
engine I was able to remove the coupling bolts, and while there also the
engine mount top bolts.
Next weekend the engine is coming out!
Ramon
#471
Seattle
> On May 30, 2015, at 11:20 AM, via Public-List
> <public-list at lists.alberg30.org> wrote:
>
> Send Public-List mailing list submissions to
> public-list at lists.alberg30.org
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> or, via email, send a message with subject or body 'help' to
> public-list-request at lists.alberg30.org
>
> You can reach the person managing the list at
> public-list-owner at lists.alberg30.org
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Public-List digest..."
>
>
> Please do NOT include the entire digest in your reply!
> ======================================================
>
>
>
> Today's Topics:
>
> 1. Navigation LED light bulbs (Randy Katz via Public-List)
> 2. Re: Cockpit floor hatch? (Jonathan Bresler via Public-List)
> 3. Re: Cockpit floor hatch? (Glenn Brooks via Public-List)
> 4. Re: Public-List Digest, Vol 3040, Issue 1
> (Glenn Brooks via Public-List)
> 5. Re: Navigation LED light bulbs (James Allocco via Public-List)
> 6. Re: Cockpit floor hatch? (Chip Dance via Public-List)
> 7. Re: Cockpit floor hatch? (George Dinwiddie via Public-List)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Fri, 29 May 2015 12:35:33 -0700
> From: Randy Katz via Public-List <public-list at lists.alberg30.org>
> To: A-30 List <public-list at lists.alberg30.org>,
> public-list-request at lists.alberg30.org
> Subject: [Public-List] Navigation LED light bulbs
> Message-ID:
> <CAFqGGGhtpvuq7VD1xtjRcC7_Zfd96sN0_ioweA5G418D+cc+dg at mail.gmail.com>
> Content-Type: text/plain; charset=UTF-8
>
> Greetings, Jonathan et al,
>
> Aqua Signal fixtures seem to be fine. I was able to simply replace the
> bulb
> in my existing anchor light with an LED version that had the right base.
> I'm very happy to have finally made the switch over.
>
> Be sure to get LEDs for navigational purpose. At Fisheries Supply in
> Seattle, those are in a different display from other LED bulbs.
>
> Randy Katz
> #249 Simple Gifts
> Seattle/Bellingham WA
>
>
>
> %%%%%%%%%%%%%%%%%%%%%%%%%%%%%
>
>
> Date: Fri, 29 May 2015 16:22:41 +0000 (UTC)
> From: Jonathan Adams via Public-List <public-list at lists.alberg30.org>
> To: Alberg 30 Public List -- Open To All
> <public-list at lists.alberg30.org>
> Subject: [Public-List] Running lights
>
>
> Well it is finally time to replace mine. Does anyone have any
> recommendations. The least expensive acceptable way seems to be to go with
> the Aqua Signal 25, but this does not take LEDs and I would like to do
> that. Most LED lights I have looked at are for larger boats.
> Any thoughts?
> Jonathan197
>
>
> ------------------------------
>
> Message: 2
> Date: Fri, 29 May 2015 15:50:01 -0400
> From: Jonathan Bresler via Public-List
> <public-list at lists.alberg30.org>
> To: John Johnston <danceswithwood at earthlink.net>, Alberg 30 Public
> List -- open to all <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Cockpit floor hatch?
> Message-ID:
> <CAHEe8TtJ1TfSGZOUs8oRpUjWG_YSdREvJApB3d2Nz1U8S-CffQ at mail.gmail.com>
> Content-Type: text/plain; charset=UTF-8
>
> For anyone is the Annapolis/Eastport area that would like to see a Bomar
> 10" round access port installed in the cockpit sole, please let me know.
> #262 Seaquin has one installed directly above the water lift muffler and
> stuffing box. Tomorrow is no good for me, but perhaps on Sunday,
> certainly
> during the work week as I work in Annapolis but live in Silver Spring.
>
> On Fri, May 29, 2015 at 2:13 PM, John Johnston via Public-List <
> public-list at lists.alberg30.org> wrote:
>
>> Hey Glenn - Is it possible to post pictures of both the process and the
>> result of your hatch?
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
>
> --
> Jonathan M Bresler
> Alberg 30 #262 Seaquin
>
>
> ------------------------------
>
> Message: 3
> Date: Sat, 30 May 2015 00:51:53 -0700
> From: Glenn Brooks via Public-List <public-list at lists.alberg30.org>
> To: John Johnston <danceswithwood at earthlink.net>
> Cc: Alberg 30 Public List -- open to all
> <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Cockpit floor hatch?
> Message-ID: <4FBCF7E1-5964-4E49-BFB5-6A3AE0A10F68 at comcast.net>
> Content-Type: text/plain; charset=us-ascii
>
> John,
>
> I can take a couple of photos tomorrow and email to you and Gord to,post
> on the web site. As you know we can't post photos on this list as it is
> ancient technology.
>
> I replaced the cockpit floor 5 or 6 years ago and don't think I have any
> pics of the rebuild hang around. Actually I might, but will need to dig
> around on my old computer to see if I can find them.
>
> It's actually very easy to describe - cut away the entire cockpit floor
> and with the whole floor gone, build a ledge with foam core to support the
> new floor. Prefabed the new floor with hatch, and lateral reinforcing
> strips every 12" in my shop and laid it on top of the ledge, bedded in FG
> structural putty, then tabbed the whole thing in with multiple layers mat
> and roving around the top and as much of the underneath as I could reach.
> Before the floor went back in, Also laid in battery boxes, degreased and
> painted the engine compartment and aft bilge, and heavily reinforced the
> bronze rudder tube assembly with fiberglass mat and roving as it was
> leaking and loose. So resolved a bunch of issues in one fell swoop, more
> or less.
>
> Glenn B.
> Dolce, 318
>
>
> Sent from my iPad
>
>> On May 29, 2015, at 11:13 AM, John Johnston
>> <danceswithwood at earthlink.net> wrote:
>>
>> Hey Glenn - Is it possible to post pictures of both the process and the
>> result of your hatch?
>
>
> ------------------------------
>
> Message: 4
> Date: Sat, 30 May 2015 01:03:07 -0700
> From: Glenn Brooks via Public-List <public-list at lists.alberg30.org>
> To: Gordon Laco <mainstay at csolve.net>, Alberg 30 Public List -- open
> to all <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Public-List Digest, Vol 3040, Issue 1
> Message-ID: <BC2AF9A6-6A94-4B06-ACC4-4367DA373071 at comcast.net>
> Content-Type: text/plain; charset=us-ascii
>
> Randy, I've used over the counter paint stripper on floorboards and
> bulkheads on several different occasions over the years with no issues.
> It didn't attack the glue, indeed didn't seem to even penetrate the veneer
> at all. I will say I put it on sparingly, used a couple of thin coats and
> scrapped each off fairly quickly, after 10 minutes maybe, as I to was
> concerned about the caustic material in the stripper aggressively eating
> into the wood glue. But, never saw any sign of damage. Once the old crud
> was out of the wood, wiped down with acetone, then thinner and sealed with
> teak oil, then applied 7 coats tung oil on the bulkheads, and I think two
> coats on the floor - enuf to seal out the dirt, but not make it slick and
> dangerous to walk on. I don't think I would worry about stripper having an
> advert us effect on the plywood.
>
> Glenn B.
>
> Sent from my iPad
>
>> On May 29, 2015, at 11:16 AM, Gordon Laco via Public-List
>> <public-list at lists.alberg30.org> wrote:
>>
>> I guess she was concerned that heat might affect the glue in veneer...
>> But
>> I've never had a problem. I like using heat because it causes the least
>> amount of wood to be removed with the coating.
>>
>> I did this job to SURPRISE's floorboards last season
>>
>> Gord #426 Surprise
>>
>>
>> On 29/05/15 2:09 PM, "Stephen gwyn via Public-List"
>> <public-list at lists.alberg30.org> wrote:
>>
>>> My neighbour, used to be (ahem) a professional stripper. She
>>> recommends heat for most applications, but not for anything
>>> with a thin veneer, like the floor boards. She was
>>> working in the Caribbean however, so she can't recommend a brand.
>>>
>>> So... thoughts?
>>>
>>> SG
>>
>>
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
> ------------------------------
>
> Message: 5
> Date: Sat, 30 May 2015 07:50:17 -0400
> From: James Allocco via Public-List <public-list at lists.alberg30.org>
> To: Randy Katz <randy.katz50 at gmail.com>, Alberg 30 Public List --
> open to all <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Navigation LED light bulbs
> Message-ID:
> <CAG8iVpxQsz_JCVpP9K1V8=tJ9ZB9byzjm2_=3gkF9CaQa3yrMA at mail.gmail.com>
> Content-Type: text/plain; charset=UTF-8
>
> Greetings,
>
> In 2012 I replaced my deck mounted Bow Lights on Barchetta Mia (1974) with
> Attwood LED 2 Mile Deck Mount Navigation Bow Lights, one red one green,
> currently $38 @ from Amazon. They mount on the original teak pads. I
> searched extensively for a deck mounted stern light to replace the light
> on the tafrail (maybe someone could correct the spelling) but I became
> convinced they are not produced. I haven't attempted to try and replace
> the bulb with an LED replacement in the tiny Perko fixtures.
>
> Jim Allocco
>
> On Fri, May 29, 2015 at 3:35 PM, Randy Katz via Public-List <
> public-list at lists.alberg30.org> wrote:
>
>> Greetings, Jonathan et al,
>>
>> Aqua Signal fixtures seem to be fine. I was able to simply replace the
>> bulb
>> in my existing anchor light with an LED version that had the right base.
>> I'm very happy to have finally made the switch over.
>>
>> Be sure to get LEDs for navigational purpose. At Fisheries Supply in
>> Seattle, those are in a different display from other LED bulbs.
>>
>> Randy Katz
>> #249 Simple Gifts
>> Seattle/Bellingham WA
>>
>>
>>
>> %%%%%%%%%%%%%%%%%%%%%%%%%%%%%
>>
>>
>> Date: Fri, 29 May 2015 16:22:41 +0000 (UTC)
>> From: Jonathan Adams via Public-List <public-list at lists.alberg30.org>
>> To: Alberg 30 Public List -- Open To All
>> <public-list at lists.alberg30.org>
>> Subject: [Public-List] Running lights
>>
>>
>> Well it is finally time to replace mine. Does anyone have any
>> recommendations. The least expensive acceptable way seems to be to go
>> with
>> the Aqua Signal 25, but this does not take LEDs and I would like to do
>> that. Most LED lights I have looked at are for larger boats.
>> Any thoughts?
>> Jonathan197
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
> ------------------------------
>
> Message: 6
> Date: Sat, 30 May 2015 10:26:00 -0600
> From: Chip Dance via Public-List <public-list at lists.alberg30.org>
> To: Alberg 30 Public List -- open to all
> <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Cockpit floor hatch?
> Message-ID: <keubk8rc2w0koydcvx75jivb.1433002696845 at email.android.com>
> Content-Type: text/plain; charset=utf-8
>
> I just acquired #456, and finally got her home two weeks ago. I'm just
> starting to learn about all the little details. ?She is a 1971 liner boat.
> ?She has a round access port in the cockpit that looks to be original
> based on the non-skid pattern around the access port. ?Did liner boats
> ship with an access port in the cockpit or is this a case of a factory
> customization or a very well done after market install??
>
> Chip ?#456
>
>
> Sent using a stone tablet and chisel.?
>
>
> -------- Original message --------
> From: Jonathan Bresler via Public-List <public-list at lists.alberg30.org>
> Date: 05/29/2015 1:50 PM (GMT-07:00)
> To: John Johnston <danceswithwood at earthlink.net>, Alberg 30 Public List --
> open to all <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Cockpit floor hatch?
>
> For anyone is the Annapolis/Eastport area that would like to see a Bomar
> 10" round access port installed in the cockpit sole, please let me know.
> #262 Seaquin has one installed directly above the water lift muffler and
> stuffing box. Tomorrow is no good for me, but perhaps on Sunday,
> certainly
> during the work week as I work in Annapolis but live in Silver Spring.
>
> On Fri, May 29, 2015 at 2:13 PM, John Johnston via Public-List <
> public-list at lists.alberg30.org> wrote:
>
>> Hey Glenn - Is it possible to post pictures of both the process and the
>> result of your hatch?
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
>
> --
> Jonathan M Bresler
> Alberg 30 #262 Seaquin
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
> ------------------------------
>
> Message: 7
> Date: Sat, 30 May 2015 14:20:57 -0400
> From: George Dinwiddie via Public-List
> <public-list at lists.alberg30.org>
> To: public-list at lists.alberg30.org
> Subject: Re: [Public-List] Cockpit floor hatch?
> Message-ID: <5569FF89.5000801 at alberg30.org>
> Content-Type: text/plain; charset=utf-8; format=flowed
>
> Chip, it's original. You can see it here:
> http://alberg30.org/maintenance/Accomodations/Table/cockpitmount.html
>
> - George
>
>> On 5/30/15 12:26 PM, Chip Dance via Public-List wrote:
>> I just acquired #456, and finally got her home two weeks ago. I'm
>> just starting to learn about all the little details. She is a 1971
>> liner boat. She has a round access port in the cockpit that looks to
>> be original based on the non-skid pattern around the access port.
>> Did liner boats ship with an access port in the cockpit or is this a
>> case of a factory customization or a very well done after market
>> install?
>>
>> Chip #456
>>
>>
>> Sent using a stone tablet and chisel.
>>
>>
>> -------- Original message --------
>> From: Jonathan Bresler via Public-List <public-list at lists.alberg30.org>
>> Date: 05/29/2015 1:50 PM (GMT-07:00)
>> To: John Johnston <danceswithwood at earthlink.net>, Alberg 30 Public
>> List -- open to all <public-list at lists.alberg30.org>
>> Subject: Re: [Public-List] Cockpit floor hatch?
>>
>> For anyone is the Annapolis/Eastport area that would like to see a Bomar
>> 10" round access port installed in the cockpit sole, please let me know.
>> #262 Seaquin has one installed directly above the water lift muffler and
>> stuffing box. Tomorrow is no good for me, but perhaps on Sunday,
>> certainly
>> during the work week as I work in Annapolis but live in Silver Spring.
>>
>> On Fri, May 29, 2015 at 2:13 PM, John Johnston via Public-List <
>> public-list at lists.alberg30.org> wrote:
>>
>>> Hey Glenn - Is it possible to post pictures of both the process and the
>>> result of your hatch?
>>> _______________________________________________
>>> These businesses support your Association:
>>> http://www.alberg30.org/store/A30supporters.html
>>> Please support them.
>>> _______________________________________________
>>> Public-List mailing list
>>> Public-List at lists.alberg30.org
>>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
> --
> ----------------------------------------------------------------------
> When I remember bygone days George Dinwiddie
> I think how evening follows morn; gdinwiddie at alberg30.org
> So many I loved were not yet dead, http://www.Alberg30.org
> So many I love were not yet born. also see:
> 'The Middle' by Ogden Nash http://idiacomputing.com
> ----------------------------------------------------------------------
>
>
>
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
> ------------------------------
>
> End of Public-List Digest, Vol 3041, Issue 1
> ********************************************
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
More information about the Public-List
mailing list