[Public-List] Lifelines/stanchions

[Michael Connolly via Public-List]

----- Original Message -----

From: "Michael Connolly" <crufone at comcast.net> 
To: "Jonathan Adams" <laughing_gull at verizon.net> 
Sent: Monday, April 25, 2016 8:46:44 AM 
Subject: Re: [Public-List] Lifelines/stanchions 

Jonathan, 
I think that Brent was speaking of the fasteners which attach the stanchions to their base, not the fasteners which hold the bases to the deck. I believe that all Alberg 30's are solid glass below the stanchion bases and not cored in that area. Mine, a non-liner boat is solid glass along the perimeter of the deck to hull juncture where the bases are mounted. 
Michael #133 

----- Original Message -----

From: "Jonathan Adams" <laughing_gull at verizon.net> 
To: "Michael Connolly" <crufone at comcast.net>, "Alberg 30 Public List -- open to all" <public-list at lists.alberg30.org> 
Sent: Sunday, April 24, 2016 8:58:48 PM 
Subject: Re: [Public-List] Lifelines/stanchions 

When you redrill the holes, drill them larger than needed, and then fill the holes with epoxy mixed with fibres. Some people will take a bent nail in a drill and clean the core out if it has been damaged.  

This way once you drill again, your bolt will be going through the epoxy and the core will be protected. 

Jonathan 
197 






From: Michael Connolly via Public-List <public-list at lists.alberg30.org> 
To: Brent Higgins <brentongl at yahoo.com>; Alberg 30 Public List -- open to all <public-list at lists.alberg30.org> 
Sent: Sunday, April 24, 2016 6:02 PM 
Subject: Re: [Public-List] Lifelines/stanchions 

Brent, 
My stanchion bases are cast bronze. So I would drill and re-tap them to set new SS set screws. I would use Lanocote or some type of anti seize grease to make it easier to adjust the set screws in the future. There should be two set screws @ 90 degrees to each other in each base. If your bases are SS then you can do the same, but SS is very tough to tap. 
Many owners don't like the set screw method and drill through the base and stanchion, then use a single pin to hold the stanchions in place  The original set screws work fine, you just need to put them on the list to check occasionally. 
Michael #133 

----- Original Message ----- 

From: "Brent Higgins via Public-List" < public-list at lists.alberg30.org > 
To: public-list at lists.alberg30.org 
Sent: Sunday, April 24, 2016 3:28:31 PM 
Subject: [Public-List] Lifelines/stanchions 

I am replacing my lifelines with dyneema and running netting around the boat, which I'm really excited about. My original stanchion base fastener holes keeping my stanchions locked in place are really worn, though. They are otherwise in great-ish shape, so I don't want to replace. Have any of you had this issue? Can I just drill them all to a slightly larger diameter, re-tap them and pop in new fasteners? If so, any recommendations/warnings to heed? We're moving onto the boat next week for the spring/summer (and maybe fall?), so lots of projects in the queue. This is a safety concern so tackling it as one of the first. Thanks in advance.  
Thanks, 
Brent 
_______________________________________________ 
These businesses support your Association: 
http://www.alberg30.org/store/A30supporters.html 
Please support them. 
_______________________________________________ 
Public-List mailing list 
Public-List at lists.alberg30.org 
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 


_______________________________________________ 
These businesses support your Association: 
http://www.alberg30.org/store/A30supporters.html 
Please support them. 
_______________________________________________ 
Public-List mailing list 
Public-List at lists.alberg30.org 
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org