[Public-List] Use of Chisels

C.B. Currier via Public-List public-list at lists.alberg30.org
Tue Mar 21 05:06:40 PDT 2017


Use 24 grit 6" Sanding disks - more like fred flintstone glued rocks to 
paper.
It is for floor sanding and takes the paint right off and gets you down 
to gelcoat quick.
I poked holes in the paper for the vacuum to trap the dust. Worked quite 
well.
I redid the whole hull one February - barrier coated and baltoplated.
I found the chemicals messy n slow, scraping (though I grew up scraping) not
effective enough as I still needed to get to gelcoat and then found the 
sanding slow
- till I came across the 24 grit.

CB Currier
Infinity #57

On 03/20/2017 01:52 PM, Wes Gardner via Public-List wrote:
> Hi All,
>
> I have NEVER used a chisel to remove bottom paint.  The old Red Devil
> scraper with a flat file in your back pocket to sharpen it is the old
> stand-by.  They make more ergonomic scrapers now but the technique remains
> the same.  Learn to sharpen your tools, they will then perform admirably.
> Several years in boat yards teach you many things (not all of them good
> :-).  I have also used a soft pad grinder with 36 grit.  Cuts fast, be
> careful.  Also when you get a scraper blade out of the package, the first
> thing you should do is use your flat file to round over the two ends, this
> will help eliminate gouging the gelcoat.
>
> Wear proper gear
>
> Wes
>
> On Mon, Mar 20, 2017 at 1:44 PM, Gordon Laco via Public-List <
> public-list at lists.alberg30.org> wrote:
>
>> I second that… the idea of using a chisel and pushing makes my hair stand
>> on end…  you could very easily do a lot of damage.  Much better to use a
>> scraper and pull…  I favour carbide blade scrapers… they are sharp out of
>> the package, stay sharp for years, and you have a lot of control over where
>> you’re digging…
>>
>> Gord #426
>>
>> On 2017-03-20, 1:02 PM, "Public-List on behalf of Chris Martin via
>> Public-List" <public-list-bounces at lists.alberg30.org on behalf of
>> public-list at lists.alberg30.org> wrote:
>>
>>      Be careful. I use paint scrapers and sharpen them regularly. I still
>> make a few nicks or deep scratches that I fill with epoxy. A little extra
>> paint doesnt bother me, as long as its attached to the hull. Scrape off the
>> loose stuff and paint.
>>      Maybe its a built in reason for being slow? :)
>>
>>            From: Anders Bro via Public-List <public-list at lists.alberg30.org
>>       To: Greg Dawson <gregdaws at aol.co.uk>; Alberg 30 Public List -- open
>> to all <public-list at lists.alberg30.org>
>>       Sent: Saturday, March 18, 2017 12:51 PM
>>       Subject: Re: [Public-List] Use of Chisels
>>
>>      HI Greg,
>>
>>      As of now, I don't have much experience, but I tried it, as you
>> suggest, using the chisel the wrong way around. In this manner, I seemed to
>> have a bit more control. The sharp edge of the chisel seemed to find its
>> way underneath the  soft paint and rode above the harder under layers. I
>> expect that in my case, it is not gelcoat, but rather an epoxy barrier
>> coat. In my limited experience, I didn't have any problem in sliding over
>> the harder underlayer. As the bottom paint adhered better, I had to use a
>> smidge more down pressure. I tried it with the chisel right side up... and
>> was a bit nervous. The PS commenter said that he used smaller width chisels
>> on the more resistant paint, but heck if you can strip the majority of the
>> boat in this manner, that would make a huge inroad along the path of
>> stripping. I did note that the taste of copper was on my tongue after my 1
>> minute trial, so there is still something nasty in the air, suggesting the
>> use of a mask, even though the majority
>>       of the paint is coming off in chunks.
>>
>>      I would wonder if this chisel approach would work with a hard paint as
>> opposed to the much softer ablative paint. As far as action goes, it looks
>> like in some instances the paint is being cut, in others it feels like the
>> chisel is splitting the paint off the undercoat. As the PS commenter
>> suggested, the chisels will need frequent sharpening. I notices a slight
>> dulling in my limited experiment...
>>
>>      He also suggested using a 2" wide chisel for the initial effort,
>> followed by narrower ones for the more stubbornly adhered paint. As soon as
>> the eBay 2" slick comes in, I will give it a try... (could it be too wide,
>> making it more difficult to move through the paint???) My paint is also
>> about 1/8" thick.
>>
>>      I hope this helps.
>>
>>      Anders
>>
>>      Sent from my iPhone
>>
>>      > On Mar 18, 2017, at 12:29 PM, Greg Dawson via Public-List <
>> public-list at lists.alberg30.org> wrote:
>>      >
>>      >
>>      > So I have the same problem with removing antifouling paint and in my
>> case the previous owner claims to have stripped the boat and applied a
>> barrier coat before applying the antifouling. In truth I think that he
>> simply applied antifouling paint over what was already there. I too have
>> looked at the various options and found them all very costly whilst being
>> potentially very environmentally unfriendly.
>>      >
>>      > By accident whilst digging around my rudder mountings discovered
>> that a standard paint scraper worked quite well (the kind that looks like a
>> screwdriver with a blade attached). At least on the thick areas. As my
>> antifouling is up to 1/8th of an inch in places it flew off. When you say
>> using the flat edge do you mean effectively upside down? I'm going to try
>> this, hopefully without gouging large chunks out of the gel coat....
>>      > _______________________________________________
>>      > These businesses support your Association:
>>      > http://www.alberg30.org/store/A30supporters.html
>>      > Please support them.
>>      > _______________________________________________
>>      > Public-List mailing list
>>      > Public-List at lists.alberg30.org
>>      > http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>      _______________________________________________
>>      These businesses support your Association:
>>      http://www.alberg30.org/store/A30supporters.html
>>      Please support them.
>>      _______________________________________________
>>      Public-List mailing list
>>      Public-List at lists.alberg30.org
>>      http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
>>
>>
>>      _______________________________________________
>>      These businesses support your Association:
>>      http://www.alberg30.org/store/A30supporters.html
>>      Please support them.
>>      _______________________________________________
>>      Public-List mailing list
>>      Public-List at lists.alberg30.org
>>      http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
>>
>>
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org





More information about the Public-List mailing list