[Public-List] Damn screws
Michael Connolly
crufone at comcast.net
Tue Jun 5 09:14:11 PDT 2018
George,
Would you like to send the pump body to me in New Bern, NC? I can work on getting the screws out for you. Least I can do for all you do for the Association. Let me know.
Michael
----- Original Message -----
From: "George Dinwiddie via Public-List" <public-list at lists.alberg30.org>
To: public-list at lists.alberg30.org
Cc: "George Dinwiddie" <gdinwiddie at alberg30.org>
Sent: Monday, June 4, 2018 1:08:14 PM
Subject: Re: [Public-List] Damn screws
Thanks, everyone, but I've got enough rat-holes without building custom
tools or trying to drill out a stainless machine screw at an arbitrary
angle. I don't need more yaks to shave.
I just want to pump out the bilge.
On 6/4/18 1:04 PM, americo silva via Public-List wrote:
> i see hate when that happens
> maybe an adapter
>
> On Mon, Jun 4, 2018 at 12:51 PM, Michael Connolly via Public-List <
> public-list at lists.alberg30.org> wrote:
>
>> George,
>> You can perhaps make an adaptor to fit the bit to the impact driver. This
>> would be helpful in the future.
>>
>> Also, what is more important to you the aluminum casting or the rubber
>> diaphragm? If the diaphragm is easily and at reasonable cost replaced. Then
>> definitely go with heat. I assume that to replace the casting means
>> replacing the pump. Using heat, heat only the aluminum near the offending
>> screw. Lots o'heat then let air cool. You can do this several times. I have
>> also used a thread loosener along with the heat. Take your bit that fits
>> and place in screw slot and tap it hard while heating. Repeat several times
>> with heat and thread loosener.
>>
>> Failing this. What do you think the diameter of the screws is? #10 or
>> 1/4"? Place aluminum casting on base of drill press and secure level as
>> possible = perpendicular to the screw. File off the head, center punch and
>> starting with new 1/16" bits, drill down thorough the screw. You might need
>> a handful of new bits for each screw. Dull drill bits will just go sideways
>> esp. in stainless, so use new bits. If you can, drill right through the
>> screw into the cavity beyond the screw body. Increase the size of the bit
>> until you reach the size of the original screw = valleys of the threads.
>> Then use a needle pick and pick out the threads which remain. Sometimes you
>> can get all the threads out. Otherwise just get the first couple of
>> threads. Then start a new tap of the correct size and carefully remove the
>> old threads being careful not to cut new threads. The idea to drill right
>> through the screw into the cavity below is so one can use compressed air or
>> thread loosener to blast out the debris a
>> s it accumulates. Removal of debris is critical to this operation.
>> Accumulations of debris will jam the tap and cause the tap to rip out the
>> original threads in the aluminum casting. Most of the time these screws go
>> into a blind hole. Sometimes the hole is deep enough or can be deepened to
>> allow you to cut new threads in the lower portion of the hole if the upper
>> threads are messed up and your new screw won't tighten up. You will need to
>> purchase a bottoming tap or make one by grinding off the end of a tapered
>> tap. Always begin with the tapered tap and follow with the bottoming tap.
>> Cleaning out debris as you go.
>>
>> Michael................hang in there.
>>
>> ----- Original Message -----
>>
>> From: "George Dinwiddie via Public-List" <public-list at lists.alberg30.org>
>> To: public-list at lists.alberg30.org
>> Cc: "George Dinwiddie" <gdinwiddie at alberg30.org>
>> Sent: Monday, June 4, 2018 8:11:29 AM
>> Subject: Re: [Public-List] Damn screws
>>
>> On 6/3/18 9:54 PM, americo silva via Public-List wrote:
>>> screw bits are not that expensive must b a hardeware store around
>>
>> Oh, I've got screw bits that fit the screw, but they don't fit the
>> impact driver.
>>
>> --
>> ----------------------------------------------------------------------
>> When I remember bygone days George Dinwiddie
>> I think how evening follows morn; gdinwiddie at alberg30.org
>> So many I loved were not yet dead, http://www.Alberg30.org
>> So many I love were not yet born. also see:
>> 'The Middle' by Ogden Nash http://idiacomputing.com
>> ----------------------------------------------------------------------
>>
>>
>>
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
--
----------------------------------------------------------------------
When I remember bygone days George Dinwiddie
I think how evening follows morn; gdinwiddie at alberg30.org
So many I loved were not yet dead, http://www.Alberg30.org
So many I love were not yet born. also see:
'The Middle' by Ogden Nash http://idiacomputing.com
----------------------------------------------------------------------
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
More information about the Public-List
mailing list