[Public-List] Roller Furler Luff Rope and Dacron Twisting

Michael Connolly crufone at comcast.net
Thu May 24 12:38:14 PDT 2018


Jonathan, 
Have you used this sail before now? Or is it a used sail you purchased to use this year? I suspect that this might be a luff wire or luff rope type of sail meant for furling but not a furler which uses a foil. Furlers without a foil use the drum and the swivel at the top to furl the sail.......there is no foil employed. 

The luff rope on a sail meant to be threaded up a foil grove is very tight to the Dacron, no way the Dacron could twist around it. The luff rope on a wire/rope sail not meant to go into a foil is very loose in the luff pocket. 

Hope this helps. 
Michael 

----- Original Message -----

From: "Jonathan Bresler via Public-List" <public-list at lists.alberg30.org> 
To: "Michael Nikolich" <mike.nikolich550 at gmail.com> 
Cc: "Jonathan Bresler" <262alberg30 at gmail.com>, "Alberg 30 Public List -- open to all" <public-list at lists.alberg30.org> 
Sent: Wednesday, May 23, 2018 5:25:37 AM 
Subject: Re: [Public-List] Roller Furler Luff Rope and Dacron Twisting 

Thank you all for your ideas and comments. 

The top and the bottom swivels (items 3 and 12 in the diagram on page 3 of 
http://www.seldenmast.com/files/1426855959/595-104-E.pdf) move easily. 
They were lubricated this spring during recommissioning with Lewmar Winch 
Grease. The snap shackles don't move as freely, but they don't have the 
ball bearings of the swivels. I can check the top swivel, perhaps 
something has happened or some foreign matter has become trapped in the 
swivel restricting its motion in a way that I have not noticed. 

The luff tape appears to be similar to 
https://www.sailmakerssupply.com/product/dacron-luff-tape/luff-tape , but 
not so nice. In the photos at sailmaker's supply, the dacron is tight 
against the material that forms the "luff rope" which goes inside the 
groove of the furler. On Constance, the dacron is not so tightly formed 
around the "luff rope". Its this dacron that twists. Does not need much 
twist to start binding, 30 degrees, perhaps less, is enough to introduce a 
third layer of dacron into the groove. 

I'll check the swivel and get some photos for everyone. 

Jonathan 

On Tue, May 22, 2018 at 11:18 PM, <mike.nikolich550 at gmail.com> wrote: 

> Jonathan, 
> 
> I’m struggling to picture what is actually getting twisted. Just the 
> Dacron? What you describe seems like a loose bolt rope of a sleeved luff, 
> not the typical luff tape designed for a furler foil. The “bead” at the 
> forward end of the luff tape should be tightly stitched in, the Dacron 
> should not be free to rotate around it. Can you send me some pictures 
> off-list? 
> 
> My initial thought is that even if your luff has a problem the root cause 
> will be elsewhere; I think Don is on the right track suspecting a swivel, 
> but I don’t know your setup. 
> 
> Mike N. 
> 
> On May 22, 2018, at 7:37 PM, Jonathan Bresler via Public-List < 
> public-list at lists.alberg30.org> wrote: 
> 
> Folks, 
> 
> Constance is my first experience with a roller furler. Hoisting the genoa 
> can be a bit of a pain. The dacron enclosing the luff rope/wire, the part 
> that goes into the groove of the foil which surrounds the headstay, 
> twists. Once it starts to twist, the dacron drags and seems to twist more, 
> trying to force three layers of dacron into the slot of the foil, in place 
> of the two layers of dacron for which it was designed. The twist is 
> clockwise viewed from above, in the same direction as the sail turns when 
> it furls. The UV protection cloth is on the port side of the sail, so the 
> sail must furl clockwise in order to leave the UV cloth on the outside. To 
> visualize this hold your right hand with your thumb pointing at your nose, 
> fingers together and naturally curving toward the palm of your right hand. 
> Your thumb is the foil. Your thumbnail is the swivel on the foil to which 
> the jib halyard attaches. Your fingertips are the leech of the genoa. 
> (its a small sail, chord length is one finger long ;) 
> 
> The way I have been handling this, is to straIghten the "luff rope" and the 
> two layers of dacron by giving them a bit of "pre-twist" 
> counter-clockwise. Hoist some sail till it starts to bind due to the 
> twist, lower a bit, pre-twist a couple feet of luff, hoist, repeat. 
> Clearly, this does not make for quick sail changes. Any idea of quickly 
> raising a second sail in other unused groove is laughable....at least the 
> "quickly" part is laughable. 
> 
> So what's up? Worn out luff rope and dacron in the sail? Dacron around 
> the luff rope has bagged over the years? I need lessons? Anyone else 
> having a similar issue? How did you fix it? 
> 
> Jonathan 
> 
> -- 
> Jonathan M Bresler 
> S/V Constance Alberg 30 #262 
> Annapolis/Eastport MD 
> _______________________________________________ 
> These businesses support your Association: 
> http://www.alberg30.org/store/A30supporters.html 
> Please support them. 
> _______________________________________________ 
> Public-List mailing list 
> Public-List at lists.alberg30.org 
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 
> 



-- 
Jonathan M Bresler 
S/V Constance Alberg 30 #262 
Annapolis/Eastport MD 
_______________________________________________ 
These businesses support your Association: 
http://www.alberg30.org/store/A30supporters.html 
Please support them. 
_______________________________________________ 
Public-List mailing list 
Public-List at lists.alberg30.org 
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 



More information about the Public-List mailing list