[Public-List] Stern Tube Bedding

Andrew Johns johnsab9 at gmail.com
Mon Apr 8 13:47:14 PDT 2019


Thanks for the replies everyone! 5200 it is.

There is a mention of though bolting the cutless bearing housing on the A30
site.

http://www.alberg30.org/maintenance/MechanicalPropulsion/CutlessBearing/Thrubolted/

This seems like the most secure method, I'm assuming the bolts clear the
"shelf" below the stuffing box?  Anyone know what size bolts they used? My
boat is 2 hours  away or I would measure myself.

Thanks,
Andrew


On Mon, Apr 8, 2019 at 2:55 PM Andrew Johns <johnsab9 at gmail.com> wrote:

> John,
> I do summer dockage and winter storage at The Moorings.  I'm currently in
> the lake side lot, in front of the little house on the right side.
>
> Andrew
>
>
>
>
>
>
> On Mon, Apr 8, 2019 at 2:10 PM John Irving via Public-List <
> public-list at lists.alberg30.org> wrote:
>
>> Andrew, where do you keep your boat in the winter?  I recently replaced
>> my cutless bearing but fortunately didn’t have that difficulty.
>>
>> John Irving
>> Scotch Bonnet #634
>> Champlain Marina
>> Colchester, Vt
>>
>> > On Apr 8, 2019, at 1:49 PM, Gordon Laco via Public-List <
>> public-list at lists.alberg30.org> wrote:
>> >
>> > Hello Hernan…
>> >
>> > The threads can be restored with complete integrity by filling the
>> holes with epoxy thickened with appropriate fibre…. once cured, drill out
>> the holes a size smaller then run a thread cutting tap in to rethread.
>> >
>> > That is quite a secure means of re-establishing your fastenings.
>> >
>> > Gordon Laco
>> > SURPRISE 426
>> >
>> >
>> >
>> >
>> >> On Apr 8, 2019, at 1:37 PM, Hernán Scarnichia via Public-List <
>> public-list at lists.alberg30.org> wrote:
>> >>
>> >> The "threads on the keel" stripped out on my boat.
>> >> When I hauled out one of the screws was gone and the other I pulled
>> with my
>> >> fingers.
>> >> In my opinion is not a strong design for a part that can see some
>> >> vibration. But nobody else seems to have had this problem.
>> >>
>> >> On Mon, Apr 8, 2019 at 7:07 AM Andrew Johns via Public-List <
>> >> public-list at lists.alberg30.org> wrote:
>> >>
>> >>> Good Morning,
>> >>> In my rapidly snowballing shaft seal project... I have removed the
>> cutlass
>> >>> bearing housing to replace worn bearing.
>> >>>
>> >>> I removed the bolts holding it to the keel and rotated it with a pipe
>> >>> wrench in an effort to get it to thread from the stern tube.
>> Unfortunately
>> >>> the whole bearing housing and stern tube assembly came out as one
>> piece.
>> >>> Fortunately its in good shape but the two pieces are hopelessly stuck
>> >>> together.
>> >>>
>> >>> Looking back though the list it appears Whitby used some sort of
>> caulk to
>> >>> bond in the assembly? Dolponite?  What is the groups thoughts on
>> using 5200
>> >>> to reinstall the stern tube/ bearing housing?
>> >>>
>> >>> Additionally, should I be worried about the threads in the keel
>> striping
>> >>> out?  It don't appear to have any metal inserts or anything of that
>> sort.
>> >>>
>> >>> Thanks,
>> >>> Andrew Johns
>> >>> Ecola # 104
>> >>> Colchester VT
>> >>> _______________________________________________
>> >>> These businesses support your Association:
>> >>> http://www.alberg30.org/store/A30supporters.html
>> >>> Please support them.
>> >>> _______________________________________________
>> >>> Public-List mailing list
>> >>> Public-List at lists.alberg30.org
>> >>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>> >>>
>> >> _______________________________________________
>> >> These businesses support your Association:
>> >> http://www.alberg30.org/store/A30supporters.html
>> >> Please support them.
>> >> _______________________________________________
>> >> Public-List mailing list
>> >> Public-List at lists.alberg30.org
>> >> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>> >
>> > _______________________________________________
>> > These businesses support your Association:
>> > http://www.alberg30.org/store/A30supporters.html
>> > Please support them.
>> > _______________________________________________
>> > Public-List mailing list
>> > Public-List at lists.alberg30.org
>> > http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
>



More information about the Public-List mailing list