[Public-List] stern tube question

Michael Connolly crufone at comcast.net
Mon Feb 4 07:38:13 PST 2019


Hello all,
It is my understanding that the stern tube was secured into the boat to provide a water tight passage for the prop shaft. There are no bearings in the stern tube on our boats. There needs to be enough clearance so the shaft does not rub against the tube, wearing a hole in it to cause a leak for sea water into the boat. No need for the tube to be absolutely concentric with the shaft as long as there is clearance for the length of the shaft inside the tube.
Michael

> On February 3, 2019 at 5:04 PM Clay Pass via Public-List <public-list at lists.alberg30.org mailto:public-list at lists.alberg30.org > wrote:
> 
> 
>     I think that test assumes that there is not any play in the rubber cutlass
>     bearing that might allow the shaft to hang low as it is resting on the
>     bearing or it is pushed over to one side or the other because of wear in
>     the bearing. I think that if you removed the cutlass bearing and housing
>     you should have been able to visibly see shaft move off center in the stern
>     tube as it was rotated.
> 
>     On Fri, Feb 1, 2019 at 10:11 PM Kris Coward via Public-List <
>     public-list at lists.alberg30.org mailto:public-list at lists.alberg30.org > wrote:
> 
>     >
> 
>         > > As a note, my wobble wasn't visible. That said, it was detectable prior
> >         to removal by uncoupling the shaft from the engine to test the
> >         alignment, rotating the shaft by one coupling bolt, testing the
> >         alignment again, and seeing that it was different. Once out, it was
> >         confirmed by rolling the shaft down a reference flat surface (one of the
> >         granite slabs at a machine shop, which are used specifically to make
> >         sure that things are really flat, though I've heard that granite
> >         countertops and mirrors also work).
> > 
> >     > 
>         > > -K
> > 
> >     > 
>         > > On Fri, Feb 01, 2019 at 10:01:12AM -0500, David Fay via Public-List wrote:
> > 
> >             > > > Don,
> > > 
> > >         > > 
> >             > > > Thank you so much for your comments. It's not what I wanted to hear but
> > > 
> > >         > > you've opened my mind to new possibilities.
> >         >
> > 
> >             > > > My initial thought was that there couldn't have been much force applied
> > > 
> > >         > > to the shaft because the wrap didn't stop the engine. Plus I have that
> >         flexible coupling, which is supposed to avoid damage in just this kind of
> >         situation -- the weak link as you call it. But we'll see. The next step
> >         will be to see if the shaft wobbles when I rotate it.
> >         >
> > 
> >             > > > David
> > >             Blue Teal #284
> > > 
> > >         > > 
> >             > > > 
> > >                 > > > > On Feb 1, 2019, at 9:39 AM, Don Campbell via Public-List <
> > > > 
> > > >             > > > 
> > >         > > public-list at lists.alberg30.org mailto:public-list at lists.alberg30.org > wrote:
> > 
> >             > > > 
> > >                 > > > > 
> > > >             > > > 
> > >                 > > > > David:
> > > >                 You have probably bent the drive shaft with the dockline as I
> > > > 
> > > >             > > > 
> > >         > > suspect that is the weakest part of your drivetrain.. If you recall, Kris
> >         Coward said he had a bent driveshaft and I have had one as well. The bend
> >         in my shaft was about 0.005" and was small enough that the machine shop I
> >         took things to managed to work that back to straight with a lathe and some
> >         sideways pressure. Stainless is very malleable, and bends easily. I am
> >         surprised though that you only have a 7/8" shaft for a diesel. They are
> >         usually a full 1" because of the extra torque developed by diesels. It the
> >         shaft did not bend, then the coupler probably gave because of that torque
> >         or, if that did not fail, a motor mount has bent. You should have that
> >         diesel on flex mounts. Whatever has been the resistance with the dockline,
> >         it will have been the torque developed by your motor that will have caused
> >         the weakest link to fail.
> > 
> >             > > > 
> > >                 > > > > Don
> > > > 
> > > >             > > > 
> > >                 > > ---Original Message----- From: David Fay via Public-List
> >                 Sent: Thursday, January 31, 2019 9:21 PM
> >                 To: Alberg 30 Public List -- open to all
> >                 Cc: David Fay
> >                 Subject: Re: [Public-List] stern tube question
> > 
> >             > 
>                 > > Michael,
> > 
> >             > 
>                 > > That's possible of course, but this is not some ancient clunker of an
> > 
> >             > 
>         engine but rather a new Beta Marine diesel installed just five years ago by
a highly competent boat restorer (Tim Lackey). I would be very surprised if
a rope wrap could twist the engine around on its engine mounts. But it's
certainly something I will have to look into.

> 
>                 > > 
> >             > 
>                 > > David
> >                 Blue Teal #284
> > 
> >             > >
>             >
>             >> On Jan 31, 2019, at 8:30 PM, Michael Grosh via Public-List <
> 
>         public-list at lists.alberg30.org mailto:public-list at lists.alberg30.org > wrote:

> 
>                 > > 
> >                     > > > 
> > >                 > > 
> >             > >> It sounds like the line wrap may have pulled the engine out of
> 
>         alignment.

> 
>                 > > 
> >             > 
>                 > > _______________________________________________
> >                 These businesses support your Association:
> >                 http://www.alberg30.org/store/A30supporters.html
> >                 Please support them.
> >                 _______________________________________________
> >                 Public-List mailing list
> >                 Public-List at lists.alberg30.org mailto:Public-List at lists.alberg30.org
> >                 http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> >                 _______________________________________________
> >                 These businesses support your Association:
> >                 http://www.alberg30.org/store/A30supporters.html
> >                 Please support them.
> >                 _______________________________________________
> >                 Public-List mailing list
> >                 Public-List at lists.alberg30.org mailto:Public-List at lists.alberg30.org
> >                 http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> > 
> >             > 
>         
> _______________________________________________
>             These businesses support your Association:
>             http://www.alberg30.org/store/A30supporters.html
>             Please support them.
>             _______________________________________________
>             Public-List mailing list
>             Public-List at lists.alberg30.org mailto:Public-List at lists.alberg30.org
>             http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> 
>         

Kris Coward http://unripe.melon.org/
GPG Fingerprint: 2BF3 957D 310A FEEC 4733 830E 21A4 05C7 1FEB 12B3
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org mailto:Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org mailto:Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org



More information about the Public-List mailing list