[Public-List] Stern tube

Kris Coward kris at melon.org
Fri May 29 08:30:04 PDT 2020


What do you mean "without removing the engine"? If the job's done by
hauling, the bearing housing's going to come off and go back on again,
so the engine's going to need to be realigned anyway.

Of course hauling the boat provides more opportunity to clean the
bottom, touch up the bottom paint, etc. than pulling the engine (and the
stern tube rebedding/resealing is easier on the hard) -- but you don't
need as big a crane to pull the engine :)

(I write this all as I'm years overdue to haul and repaint the bottom,
but don't know how much it's worth looking for a yard that isn't booked
solid with slower, socially-distanced launches now that we're allowed to
launch boats in Ontario again. Of course, if I hadn't repowered to
electric, there'd be plenty of available cranes to pull the engine with
-- but as things stand I can just lift the motor out with my bare
hands.)

-Kris

On Fri, May 29, 2020 at 07:31:55AM -0400, Andrew Johns via Public-List wrote:
> I think you will have to haul out to fix this one...
> 
> If you have a cockpit floor access hatch or (add one) It is possible to
> re-bed the stern tube without removing the engine, but it does involve a
> bit of boat yoga.
> 
> When I removed the bearing housing the 54 year old sealant crubles when i
> removed it and the stern tube came with it.    I removed the propshaft  and
> rebedded with 5200.
> 
> 
> 
> On Fri, May 29, 2020 at 2:11 AM Kris Coward via Public-List <
> public-list at lists.alberg30.org> wrote:
> 
> >
> > If you recently reinstalled the housing with fresh sealant on clean
> > surfaces, it might be worth considering whether the leak is in the joint
> > between the cutless bearing housing and the stern tube. It _might_ even
> > be possible to tighten up this joint (or pop out and (re)tape the
> > threads on the tube) without having to haul.
> >
> > -K
> >
> > On Thu, May 28, 2020 at 07:09:22PM +0000, Gerard Kuperus via Public-List
> > wrote:
> > > Thanks again David, and George,
> > >
> > > It seems more and more like a haul-out is required. I cannot imagine
> > that I did not apply enough sealant when I reinstalled the housing, but in
> > this case I do hope I messed up, because replacing the stern tube would be
> > a major undertaking, and which I think can only be done by moving the
> > engine.
> > >
> > > I will keep you posted!
> > >
> > > G
> > >
> > >
> > > _______________________________________________
> > > These businesses support your Association:
> > > http://www.alberg30.org/store/A30supporters.html
> > > Please support them.
> > > _______________________________________________
> > > Public-List mailing list
> > > Public-List at lists.alberg30.org
> > > http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> >
> > --
> > Kris Coward                                     http://unripe.melon.org/
> > GPG Fingerprint: 2BF3 957D 310A FEEC 4733  830E 21A4 05C7 1FEB 12B3
> > _______________________________________________
> > These businesses support your Association:
> > http://www.alberg30.org/store/A30supporters.html
> > Please support them.
> > _______________________________________________
> > Public-List mailing list
> > Public-List at lists.alberg30.org
> > http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> >
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

-- 
Kris Coward					http://unripe.melon.org/
GPG Fingerprint: 2BF3 957D 310A FEEC 4733  830E 21A4 05C7 1FEB 12B3


More information about the Public-List mailing list