[Public-List] Public-List Digest, Vol 4004, Issue 1
Sheldon Shikoluk
shikshikoluk at gmail.com
Mon May 11 15:17:39 PDT 2020
I replaced mine by edge glueing two pieces of 1x6 teak using dowels. I used
old taffrail as template for curve. Since the liner overlaps the hull at
stern I had to trim off excess liner so it was even across top of transom.
I then got a measurement of distance from liner to outside edge of hull and
distance from top of taffrail to top of transom. I then epoxied another
piece of teak to bottom of curved piece. Once it setup I sanded outside
flush and dry fit it. Then I bedded it down with interlux bedding compound
and screws. When I hauled out I used a little boat life caulk around
outside sea.m
On Mon, May 11, 2020, 4:21 PM <public-list-request at lists.alberg30.org>
wrote:
> Send Public-List mailing list submissions to
> public-list at lists.alberg30.org
>
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> or, via email, send a message with subject or body 'help' to
> public-list-request at lists.alberg30.org
>
> You can reach the person managing the list at
> public-list-owner at lists.alberg30.org
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of Public-List digest..."
>
>
> Please do NOT include the entire digest in your reply!
> ======================================================
>
>
>
> Today's Topics:
>
> 1. Replacing Taffrail (Carla)
> 2. Re: Replacing Taffrail (George Dinwiddie)
> 3. Re: Replacing Taffrail (Don Campbell)
> 4. Re: Replacing Taffrail (Andrew Johns)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Mon, 11 May 2020 11:37:07 -0400
> From: Carla <hazlegrove at aol.com>
> To: public-list at lists.alberg30.org
> Subject: [Public-List] Replacing Taffrail
> Message-ID: <C8DF9DBA-CAF9-42E5-8579-6308DF07EEEE at aol.com>
> Content-Type: text/plain; charset=utf-8
>
> I am looking to replace the 50 year old taffrail on Quest 433, a liner
> boat that has the shorter Taffrail. I measure it at 3/8? but have no idea
> how much may have been sanded away over the years. It does however mate up
> relatively well where it meets the quarter cap rails. It appears to have
> been originally made using three 4? wide boards glued together and cut to
> the radius of the raised deck molding. So far I have been able to source
> 1/2? up to 6? wide. After plaining down to 3/8? this would require only
> two glue joints.
>
> I have a friend who is builds antique furniture and has agreed to help
> with the woodworking. We will use the existing taffrail as a template.
> Other than removing the 50 year old bungs and likely rusted fasteners does
> anybody have any thoughts or advice regarding this work. Also would I be
> advised to try and locate a 12? wide board and avoid glue joints
> altogether.
>
> Thanks, for any advice and/or suggestions for sourcing the teak lumber.
>
> Richard Hazlegrove
> Quest433
> Mobjack Bay, VA
>
>
> ------------------------------
>
> Message: 2
> Date: Mon, 11 May 2020 12:24:52 -0400
> From: George Dinwiddie <gdinwiddie at alberg30.org>
> To: public-list at lists.alberg30.org
> Subject: Re: [Public-List] Replacing Taffrail
> Message-ID: <05414f5d-d0a5-3021-f6f7-4e5b3412cfa1 at alberg30.org>
> Content-Type: text/plain; charset=utf-8; format=flowed
>
> Richard,
>
> http://alberg30.org/maintenance/HullDeck/NewerTaffrail/ shows the
> process I used to replace the taffrail on Calypso, #543. My taffrail was
> made by Cy Fishburn, who laminated strips of teak together to give a
> curved shape with less waste. It's held up pretty well, and would have
> done better if I'd kept it varnished.
>
> - George
>
> On 5/11/20 11:37 AM, Carla via Public-List wrote:
> > I am looking to replace the 50 year old taffrail on Quest 433, a liner
> boat that has the shorter Taffrail. I measure it at 3/8? but have no idea
> how much may have been sanded away over the years. It does however mate up
> relatively well where it meets the quarter cap rails. It appears to have
> been originally made using three 4? wide boards glued together and cut to
> the radius of the raised deck molding. So far I have been able to source
> 1/2? up to 6? wide. After plaining down to 3/8? this would require only
> two glue joints.
> >
> > I have a friend who is builds antique furniture and has agreed to help
> with the woodworking. We will use the existing taffrail as a template.
> Other than removing the 50 year old bungs and likely rusted fasteners does
> anybody have any thoughts or advice regarding this work. Also would I be
> advised to try and locate a 12? wide board and avoid glue joints altogether.
> >
> > Thanks, for any advice and/or suggestions for sourcing the teak lumber.
> >
>
> --
> ----------------------------------------------------------------------
> When I remember bygone days George Dinwiddie
> I think how evening follows morn; gdinwiddie at alberg30.org
> So many I loved were not yet dead, http://www.Alberg30.org
> So many I love were not yet born. also see:
> 'The Middle' by Ogden Nash http://idiacomputing.com
> ----------------------------------------------------------------------
>
>
>
>
>
> ------------------------------
>
> Message: 3
> Date: Mon, 11 May 2020 17:50:42 +0000
> From: "Don Campbell" <dk.campbell at xplornet.ca>
> To: "Alberg 30 Public List -- open to all"
> <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Replacing Taffrail
> Message-ID: <em33e7ef50-ab43-4e9e-a140-a6c1c9a1446e at desktop-kadjbdn>
> Content-Type: text/plain; format=flowed; charset=utf-8
>
> If you use "glue " on teak I suggest you consider using G-Flex epoxy,
> developed for oily woods.
> Don
>
> ------ Original Message ------
> From: "George Dinwiddie via Public-List"
> <public-list at lists.alberg30.org>
> To: public-list at lists.alberg30.org
> Cc: "George Dinwiddie" <gdinwiddie at alberg30.org>
> Sent: 2020-05-11 12:24:52 PM
> Subject: Re: [Public-List] Replacing Taffrail
>
> >Richard,
> >
> >http://alberg30.org/maintenance/HullDeck/NewerTaffrail/ shows the
> process I used to replace the taffrail on Calypso, #543. My taffrail was
> made by Cy Fishburn, who laminated strips of teak together to give a curved
> shape with less waste. It's held up pretty well, and would have done better
> if I'd kept it varnished.
> >
> > - George
> >
> >On 5/11/20 11:37 AM, Carla via Public-List wrote:
> >>I am looking to replace the 50 year old taffrail on Quest 433, a liner
> boat that has the shorter Taffrail. I measure it at 3/8? but have no idea
> how much may have been sanded away over the years. It does however mate up
> relatively well where it meets the quarter cap rails. It appears to have
> been originally made using three 4? wide boards glued together and cut to
> the radius of the raised deck molding. So far I have been able to source
> 1/2? up to 6? wide. After plaining down to 3/8? this would require only
> two glue joints.
> >>
> >>I have a friend who is builds antique furniture and has agreed to help
> with the woodworking. We will use the existing taffrail as a template.
> Other than removing the 50 year old bungs and likely rusted fasteners does
> anybody have any thoughts or advice regarding this work. Also would I be
> advised to try and locate a 12? wide board and avoid glue joints altogether.
> >>
> >>Thanks, for any advice and/or suggestions for sourcing the teak lumber.
> >>
> >
> >-- ----------------------------------------------------------------------
> > When I remember bygone days George Dinwiddie
> > I think how evening follows morn; gdinwiddie at alberg30.org
> > So many I loved were not yet dead, http://www.Alberg30.org
> > So many I love were not yet born. also see:
> > 'The Middle' by Ogden Nash http://idiacomputing.com
> > ----------------------------------------------------------------------
> >
> >
> >
> >_______________________________________________
> >These businesses support your Association:
> >http://www.alberg30.org/store/A30supporters.html
> >Please support them.
> >_______________________________________________
> >Public-List mailing list
> >Public-List at lists.alberg30.org
> >http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
>
> ------------------------------
>
> Message: 4
> Date: Mon, 11 May 2020 15:17:36 -0400
> From: Andrew Johns <johnsab9 at gmail.com>
> To: Don Campbell <dk.campbell at xplornet.ca>, Alberg 30 Public List --
> open to all <public-list at lists.alberg30.org>
> Subject: Re: [Public-List] Replacing Taffrail
> Message-ID:
> <CAM5xwU5CzRknV_FUAd7a=
> bJ0P7nMP2gs2ya31GX6yfKhF-ZpNw at mail.gmail.com>
> Content-Type: text/plain; charset="UTF-8"
>
> I would suggest looking into salvage teak. I could not find "new teak" that
> matched the original.
>
> On Mon, May 11, 2020 at 1:50 PM Don Campbell via Public-List <
> public-list at lists.alberg30.org> wrote:
>
> > If you use "glue " on teak I suggest you consider using G-Flex epoxy,
> > developed for oily woods.
> > Don
> >
> > ------ Original Message ------
> > From: "George Dinwiddie via Public-List"
> > <public-list at lists.alberg30.org>
> > To: public-list at lists.alberg30.org
> > Cc: "George Dinwiddie" <gdinwiddie at alberg30.org>
> > Sent: 2020-05-11 12:24:52 PM
> > Subject: Re: [Public-List] Replacing Taffrail
> >
> > >Richard,
> > >
> > >http://alberg30.org/maintenance/HullDeck/NewerTaffrail/ shows the
> > process I used to replace the taffrail on Calypso, #543. My taffrail was
> > made by Cy Fishburn, who laminated strips of teak together to give a
> curved
> > shape with less waste. It's held up pretty well, and would have done
> better
> > if I'd kept it varnished.
> > >
> > > - George
> > >
> > >On 5/11/20 11:37 AM, Carla via Public-List wrote:
> > >>I am looking to replace the 50 year old taffrail on Quest 433, a liner
> > boat that has the shorter Taffrail. I measure it at 3/8? but have no idea
> > how much may have been sanded away over the years. It does however mate
> up
> > relatively well where it meets the quarter cap rails. It appears to have
> > been originally made using three 4? wide boards glued together and cut to
> > the radius of the raised deck molding. So far I have been able to source
> > 1/2? up to 6? wide. After plaining down to 3/8? this would require only
> > two glue joints.
> > >>
> > >>I have a friend who is builds antique furniture and has agreed to help
> > with the woodworking. We will use the existing taffrail as a template.
> > Other than removing the 50 year old bungs and likely rusted fasteners
> does
> > anybody have any thoughts or advice regarding this work. Also would I be
> > advised to try and locate a 12? wide board and avoid glue joints
> altogether.
> > >>
> > >>Thanks, for any advice and/or suggestions for sourcing the teak lumber.
> > >>
> > >
> > >--
> ----------------------------------------------------------------------
> > > When I remember bygone days George Dinwiddie
> > > I think how evening follows morn; gdinwiddie at alberg30.org
> > > So many I loved were not yet dead, http://www.Alberg30.org
> > > So many I love were not yet born. also see:
> > > 'The Middle' by Ogden Nash http://idiacomputing.com
> > > ----------------------------------------------------------------------
> > >
> > >
> > >
> > >_______________________________________________
> > >These businesses support your Association:
> > >http://www.alberg30.org/store/A30supporters.html
> > >Please support them.
> > >_______________________________________________
> > >Public-List mailing list
> > >Public-List at lists.alberg30.org
> > >http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> >
> > _______________________________________________
> > These businesses support your Association:
> > http://www.alberg30.org/store/A30supporters.html
> > Please support them.
> > _______________________________________________
> > Public-List mailing list
> > Public-List at lists.alberg30.org
> > http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> >
>
>
> ------------------------------
>
> Subject: Digest Footer
>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
> ------------------------------
>
> End of Public-List Digest, Vol 4004, Issue 1
> ********************************************
>
More information about the Public-List
mailing list