[Alberg30] Cutlass bearing removal

Mike Lehman sail_505 at hotmail.com
Thu Apr 24 10:46:02 PDT 2003


Let us know when you get to the rudder post, I've completely re-built this 
too. Good luck with your cutlass bearing.



Mike Lehman
"Gilleleje" #505





----Original Message Follows----
From: Bob <bob at fox.nstn.ca>
Reply-To: Alberg 30 public list <public-list at alberg30.org>
To: "'Alberg 30 public list'" <public-list at alberg30.org>
Subject: RE: [Alberg30] Cutlass bearing removal
Date: Thu, 24 Apr 2003 14:08:24 -0300

Richard,

Thanks go to you and to others on this list who has replied to my
postings on this task.

It has been a great help.
The rudder post area is next when I finish the shaft and cutlass bearing
project.

Bob
A30 #560


-----Original Message-----
From: public-list-bounces at alberg30.org
[mailto:public-list-bounces at alberg30.org] On Behalf Of
richard.hazlegrove at wachovia.com
Sent: April 24, 2003 1:21 PM
To: Alberg 30 public list
Subject: RE: [Alberg30] Cutlass bearing removal


Bob,  as you twist the flange,  it could be stuck on the threads and you
are simply getting some elastic effect from the gobs of sealant that
holds
the tube inside the boat.  You will probably need to get a wrench on the
tube from the inside so that you can put greater torque to unscrew the
flange.

You mentioned a leak near the rudder stuffing box as your next project.
A
couple of comments that may help.  There is not much going on in the
rudder
stuffing box (compared to the prop stuffing box) that wears them out.  I
can't speak for others but on #433, the leak was around the glassed area
where the rudder tube entered the interior of the hull.  It appears to
be
just slightly above the water line and only leaked when wave action or
weight in the cockpit pushed the area slightly below the waterline.  In
my
case I repacked the stuffing box and still had a leak.  Only then did I
notice on a choppy day that the water was seeping around the tube.  I
was
able to repair this by cleaning the metal and glass area and wrapping
1/2"
by 8" strips of glass cloth around the shaft and down onto the existing
glass area.  This has been trouble free for four or five years.  My
guess
is that someone tried to loosen the packing nut with only one wrench and
twisted the tube.  This broke the seal.  So be careful when you try to
repack the rudder stuffing box so that you don't create or make worse
this
problem.  Good Luck

Richard Hazlegrove
Quest 433


  +---------------------------------------------------------------+
  |                This Old Boat by Don Casey                     |
  | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
  +---------------------------------------------------------------+

Public-list mailing list -- Public-list at alberg30.org
http://www.alberg30.org/mailman/listinfo/public-list
To unsubscribe: email to Public-list-request at alberg30.org
Include command "unsubscribe <password>" in subject or body.
Use command "help" for more options.

  +---------------------------------------------------------------+
  |                This Old Boat by Don Casey                     |
  | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
  +---------------------------------------------------------------+

Public-list mailing list -- Public-list at alberg30.org
http://www.alberg30.org/mailman/listinfo/public-list
To unsubscribe: email to Public-list-request at alberg30.org
Include command "unsubscribe <password>" in subject or body.
Use command "help" for more options.


_________________________________________________________________
MSN 8 helps eliminate e-mail viruses. Get 2 months FREE*.  
http://join.msn.com/?page=features/virus

 +---------------------------------------------------------------+
 |                This Old Boat by Don Casey                     |
 | http://www.amazon.com/exec/obidos/ASIN/0071579931/alberg30-20 |
 +---------------------------------------------------------------+

Public-list mailing list -- Public-list at alberg30.org
http://www.alberg30.org/mailman/listinfo/public-list
To unsubscribe: email to Public-list-request at alberg30.org
Include command "unsubscribe <password>" in subject or body.
Use command "help" for more options.

 1051206362.0


More information about the Public-List mailing list