[Public-list] Water tank problem on older boats (or, boat fal ling apart, ...

Todd Redhead todd.redhead at sympatico.ca
Sun Jan 2 21:17:38 PST 2005


Actually what I found was a series of cracks on the inside of the tank down 
the 'seam' front edge of the hull.  What I had noticed was after draining 
all the water out of the tank and drying it out, when I came back the next 
morning there was water in the bottom again.  What was happening was the 
water was seeping through the cracks and into the tank.  I have left it open 
this winter and in the spring I hope to just paint on a layer of epoxy to 
seal off the cracks and prevent any further water from coming in.  Hopefully 
that will help with my little growth problem.

The port that I installed is in the top of the tank.  I has not leaked yet. 
I try to leave the tank full all the time as I feel the boat is more sturdy 
in heavy waves.  It tends to 'yaw' less and cut through the waves better. 
It has not leaked even when I have had her leaning way over.

I used just a standard 6" screw in type access port.  Mine is clear but you 
can also get them in white.

You should also be able to see the tank from under the 'beds' on either side 
of the v-berth.  Strathgowan has lift out access boards under the beds that 
give access to the underside area.  You should be able to see the top of the 
tank from there also.  You can also pull out the drawer on the port side to 
see the edge of the tank, I think.  Any of these access points should get 
you close enough to see where the water is coming from.

Todd
----- Original Message ----- 
From: "Amy & David Swanson" <zira at bellsouth.net>
To: "Alberg 30 Public List -- open to all" <public-list at alberg30.org>
Sent: Sunday, January 02, 2005 8:17 PM
Subject: Re: [Public-list] Water tank problem on older boats (or,boat fal 
ling apart, ...


> That set-up would certainly let me see what is going on.  Your captions 
> mention cracks, did you have to do any repair on the tank?  I guess a good 
> port & a good installation are critical since this would be below the 
> level of water in the tank.  What did you use for a port?  Unless I find 
> some other explanation for the water, I will probably go the same way.
>
> David Swanson
> Strayaway Child
> Alberg 30 #229
>
> ----- Original Message ----- 
> From: "Todd Redhead" <todd.redhead at sympatico.ca>
> To: "Alberg 30 Public List -- open to all" <public-list at alberg30.org>
> Sent: Sunday, January 02, 2005 10:00 AM
> Subject: Re: [Public-list] Water tank problem on older boats (or,boat fal 
> ling apart, ...
>
>
>> Hello David,
>>
>> I cut an access port into my watertank this past summer.   You can see a 
>> picture of how it looks here: 
>> http://www3.sympatico.ca/todd.redhead/Boat/MiscPhotos.html
>>
>> It was not hard to do.  Just take out the screws in the top of the little 
>> seat, then pry up the fitted piece of plywood.  I cut a finger hole into 
>> it so that I could pull it up more easily.  Then I cut the hole, and 
>> installed the access port with 5200.  Works great and does not leak even 
>> when completely full.  As you can also see in the picture beside it, I 
>> had some growth!  As for your leak, it might be the water tank but I 
>> doubt it. My tank was solid!  I don't see how it could leak unless it is 
>> damaged somehow. I think there were 2 different types of tanks used, one 
>> like mine where everything is glass and another one that had a metal top 
>> that was riveted into place.  I understand that the ones with the metal 
>> top could develop leaks at the seams but on the all glass ones, I don't 
>> think I've ever heard of them leaking.
>>
>> Todd
>> Strathgowan #400
>
>
>
> -- 
> No virus found in this outgoing message.
> Checked by AVG Anti-Virus.
> Version: 7.0.298 / Virus Database: 265.6.7 - Release Date: 12/30/2004
>
> _______________________________________________
> Public-list mailing list
> Public-list at alberg30.org
> http://alberg30.org/mailman/listinfo/public-list
> 



 1104729458.0


More information about the Public-List mailing list