[Public-List] Lifting boat by rudder

crufone at comcast.net crufone at comcast.net
Wed Nov 12 09:47:32 PST 2008



Ed, 

Knowing the previous owner, he was a kind heart, leather tough type of fellow.  He took wonderful care of the boat.  I suspect that the yard after hearing the suggestion were not given any choice in the matter........... ;-). 

Michael 
----- Original Message ----- 
From: "edward schroeder" <eddiediver at sbcglobal.net> 
To: "Alberg 30 Public List -- open to all" <public-list at lists.alberg30.org> 
Sent: Wednesday, November 12, 2008 12:09:44 PM GMT -05:00 US/Canada Eastern 
Subject: Re: [Public-List] Lifting boat by rudder 

Is the operative word "Suggested"? Ed Schroeder #303 

--- On Wed, 11/12/08, crufone at comcast.net <crufone at comcast.net> wrote: 

From: crufone at comcast.net <crufone at comcast.net> 
Subject: [Public-List] Lifting boat by rudder 
To: "Alberg, Public List" <public-list at alberg30.org> 
Date: Wednesday, November 12, 2008, 10:14 AM 


C.B., 



My understanding is that once the yard realized that the strap was misplaced 
they stopped lifting and repositioned the aft strap before the final haul out.  
The owner was present and witnessed their mistake and suggested that the yard 
repair the damage done to his boat. 



Michael 


WOW! the picked up the boat with one strap on the rudder ... lucky they 
didn't loose the boat ! 
-- 
C.B. Currier 
Infinity #57 
Daybreak #458 

crufone at comcast.net wrote: 
> 
> 

> Hi Daniel, 
> 
> 
> 
> Just 
before I purchased my boat the yard began to lift it and the strap 
> was on the rudder.  This caused the rudder to slam to one side, 
which 
> broke the tiller end fitting but not the wooden 
tiller!!!  The yard at 
> their cost replaced both the tiller 'H' 
fitting and the rudder post cap 
> with a new Edson set. While I 
was not there the previous owner mentioned 
> that the yard had to 
mill a key slot into the original rudder post. 
> Apparently they 
did this while the rudder and post was in location on the 
> 
boat.  They must have set up some sort of fixture and used a cutter to 
> mill the keyway.  I have not taken this apart to see how good a 
job they 
> did.  While sailing the tiller is centered nicely and 
the fitting appears 
> to be tight on the rudder post.  My boat is 
a 1966 model, Hull #133. 
> 
> 
> 
> I have 
heard that the earlier boats used a pinch bolt set up to hold this 
> fitting on and the later ones used a key system.  I believe that 
_______________________________________________ 
These businesses support your Association: 
http://www.alberg30.org/store/A30supporters.html 
Please support them. 
_______________________________________________ 
Public-List mailing list 
Public-List at lists.alberg30.org 
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 
_______________________________________________ 
These businesses support your Association: 
http://www.alberg30.org/store/A30supporters.html 
Please support them. 
_______________________________________________ 
Public-List mailing list 
Public-List at lists.alberg30.org 
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 

 1226512052.0


More information about the Public-List mailing list