[Public-List] Pre-liner water tank cover leaking

Jeffrey fongemie at gmail.com
Tue May 3 13:01:19 PDT 2011


Yes my tank is vented. The bronze cover plate has a large intake tube
that goes to the deck, and a small bronze pipe that winds into the
anchor area up at the bow for venting.

-jeff

On Tue, May 3, 2011 at 3:36 PM, Roger L. Kingsland <r.kingsland at ksba.com> wrote:
> John,
>
> My pre liner water tank is in the same place as yours with the round filler
> and drainer top similar to the one Jeff describes at the fore/aft middle of
> the tank near the port side.  I cut a trap door in the seat between the V
> berths and installed a round, clear plastic access port in the tank top a
> few inches under the seat.  It could be used to fill the tank (more trouble
> but one less hole in the deck) but you would still need a separate fitting
> for outgoing water. Question, do water tanks need to be vented, suppose so.
>
> Roger 148
>
> -----Original Message-----
> From: public-list-bounces at lists.alberg30.org
> [mailto:public-list-bounces at lists.alberg30.org] On Behalf Of mahseer at kos.net
> Sent: Tuesday, May 03, 2011 3:23 PM
> To: fongemie at gmail.com; Alberg 30 Public List -- open to all
> Subject: Re: [Public-List] Pre-liner water tank cover leaking
>
> It is interesting because my pre liner boat 1969 #380 has the water tank
> in the centre below the "V" berth.  In your case create extra thickness
> over the current hole with glass then replace with a transparent cover,
> this way you can view without removing the top.
>
> John boor
> MAHSEER #380
>
>
>> Hi everyone,
>>
>> Seagrass is a pre-liner boat, and I'm using the original water tank in
>> the port side v-berth. The tank is built in to the hull and has a
>> simple 5 inch hole in the top where a bronze cover is screwed into the
>> top of the tank. Trouble is, small screws into the thin fiberglass top
>> of the tank hold poorly, and we keep getting leaks. If we fill the
>> tank from the outside deck fill we need to be careful to fill the tank
>> no more than 3/4 full or it leaks. I've taken the cover off, cleaned
>> both surfaces, re-gooped with 4200 and reattached the screws and we
>> still get leaks. The screws just don't hold well.  Note that the cover
>> includes the fill pipe, and fittings that lead to the sink.
>>
>> Anyone else go through this? have a fix?
>>
>>
>> -jeff
>>
>>
>>
>> Jeff Fongemie
>> #116 Seagrass
>>
>> http://picasaweb.google.com/fongemie
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>
>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>



-- 
Jeffrey Fongemie

 1304452879.0


More information about the Public-List mailing list