[Public-List] Paint stripper

John's Email cooler2k at yahoo.com
Fri Jan 31 13:20:17 PST 2014


I have a lot of peel off the "corrugated" aspect of the interior roving. I've sanded where I could, but in these areas sanding is not effective. Hence my next move is toward chemicals.

J

Sent from my iPhone

On Jan 31, 2014, at 16:15, Mike Lehman <sail_505 at hotmail.com> wrote:

> I think you will need different products for latex vs. oil based. The most effective thing I have used is coarse grit sandpaper...what a mess though!
> 
> 
> 
> 
> ~~~_/)_/)~~ Mike Lehman ~~_/)~~~
> 
> 
> -----Original Message----- From: John's Email
> Sent: Friday, January 31, 2014 4:03 PM
> To: Alberg 30 Public List -- open to all
> Subject: Re: [Public-List] Paint stripper
> 
> Hello Mike,
> 
> Both. Though the majority is in the salon and is oil-base enamel, probably at one time semi-gloss. There has been some interior work in the head & closet, a poor job, using latex. No idea what if any primers were used.
> 
> JC
> 
> 
> Sent from my iPhone
> 
> On Jan 31, 2014, at 15:37, Mike Lehman <sail_505 at hotmail.com> wrote:
> 
>> The question is...are you removing latex or oil-based paint?
>> 
>> 
>> 
>> 
>> ~~~_/)_/)~~ Mike Lehman ~~_/)~~~
>> 
>> 
>> -----Original Message----- From: John's Email
>> Sent: Friday, January 31, 2014 3:33 PM
>> To: Alberg 30 Public List -- open to all
>> Subject: Re: [Public-List] Paint stripper
>> 
>> Thank you, Glenn. I had hoped that was the case. But I had a nagging nightmare that my boat was turning to gooe while my wife stood by saying
>> " You should've asked the 'List'! "
>> Thanks again  :)
>> 
>> JC
>> 
>> 
>> Sent from my iPhone
>> 
>> On Jan 31, 2014, at 15:26, Glenn Brooks <brooks.glenn at comcast.net> wrote:
>> 
>>> John,  I have used several brands of paint strippers on my interior and found they take quite a while to eat into the underlaying FG.  I think you will find if you put a light to moderate coat on the paint the stripperwill dry out and/or neutralize itself on the paint before etching the glass.
>>> 
>>> Also I usually sand and clean the surface afterwards with thinner and a sponge to flush any residual away.  (Alternately, some  of these are water soluble so maybe use water, I think)
>>> 
>>> Usually one needs quite a heavy application of stripper and a long soak period to have a meaningful impact on the glass substrate.
>>> 
>>> Cheers
>>> Glenn B.
>>> Dolce 318
>>> 
>>> Sent from my iPad
>>> 
>>>> On Jan 31, 2014, at 11:56 AM, John's Email <cooler2k at yahoo.com> wrote:
>>>> 
>>>> Hello All,
>>>> Can anyone recommend a chemical paint stripper to use in the salon and head on the interior of the hull (obviously non-liner boat) that will not have a negative effect on the underlying fiberglass?
>>>> 
>>>> Thank you,
>>>> John C.
>>>> 
>>>> Sent from my iPhone
>>>> _______________________________________________
>>>> These businesses support your Association:
>>>> http://www.alberg30.org/store/A30supporters.html
>>>> Please support them.
>>>> _______________________________________________
>>>> Public-List mailing list
>>>> Public-List at lists.alberg30.org
>>>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>>> _______________________________________________
>>> These businesses support your Association:
>>> http://www.alberg30.org/store/A30supporters.html
>>> Please support them.
>>> _______________________________________________
>>> Public-List mailing list
>>> Public-List at lists.alberg30.org
>>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>> _______________________________________________
>> These businesses support your Association:
>> http://www.alberg30.org/store/A30supporters.html
>> Please support them.
>> _______________________________________________
>> Public-List mailing list
>> Public-List at lists.alberg30.org
>> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org 
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

 1391203217.0


More information about the Public-List mailing list