[Public-List] Butyl and Polycarbonate

Eric Chavigny via Public-List public-list at lists.alberg30.org
Tue Oct 7 16:36:47 PDT 2014


The other thing to take into consideration is the UV protection of either polycarbonate or acrylics both plastics will show significant yellowing after few years outdoor.  

When buying at home depot and such it is not always easy to get the proper grade with UV protection

Eric



> On Oct 7, 2014, at 09:45, Bill Wallace via Public-List <public-list at lists.alberg30.org> wrote:
> 
> If you read those lists, things like butyl acetate are problems, but the chemical in butyl tape, isobutyl isn't listed as a problem.  That isn't definitive, as I couldn't find a positive statement about isobutyl being safe.  If you are using polycarbonate, expect to redo the portlights every 5-7 years.  That is what I was replacing and mine were nearly opaque after about 8 years.   I will watch mine and see if there are any problems, but so far after 1 summer they look good with the butyl tape - it isn't clear how long it would take to react if there is going to be a problem.  For sure, cleaning up butyl is far easier than cleaning silicone, so if I have to replace them in a few years, it will be a much small job than the first replacement was.
> 
> Bill.
> 
> 
> On Monday, October 6, 2014 4:29 PM, Greg Bover via Public-List <public-list at lists.alberg30.org> wrote:
> 
> 
> 
> When I redid my port lights a few years ago it wasn't because they leaked,
> it was because I couldn't see out of them anymore because of fogging. When I
> got the boat they were an unknown plastic and caulked with what appeared to
> be butyl. I use polycarbonate in my business and I knew that it was subject
> to embrittlement and fogging when exposed to certain chemicals. I did some
> research and found lists like the ones at
> www.palramhort.com/pdffiles/PC...Info/PC_Chemical_Resistance.pdf  and
> http://www.holophane.com/hlp_library/brochures/HL-2445.pdf.
> As there are various sorts of butyl and butyl compounds on the lists of
> chemicals to avoid in contact with polycarbonate I opted to use a Dow UV
> resistant silicone. I had to do quite a bit of masking to make a neat job of
> it, but so far, (two years) it has held up well with no sign of fogging.
> It seemed to me that the best combination would have been safety glass with
> butyl, but the estimate for just the glass for the four larger ports was
> $250, whereas I could use off cuts from my shop for nothing. Ahh.life on a
> shoestring.
> 
> Greg Bover
> A-30 #114
> PENSIVE
> Gloucester
> 
> Gregory R Bover
> V.P. Operations, Project Manager
> C. B. Fisk, Inc.
> www.cbfisk.com
> 978 283 1909
> 
> 
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

 1412725007.0


More information about the Public-List mailing list