[Public-List] Spinnaker advice

Gordon Laco mainstay at csolve.net
Mon Apr 30 09:53:08 PDT 2018


Another way is to treat the downhaul as if it were a vang… fix a block to the forward side of the heel of the mast… nice thing about that is that you don’t have to adjust the downhaul every time you adjust the foreguy.

Gordon Laco
www.gordonlaco.com




> On Apr 30, 2018, at 12:49 PM, Jon Budington via Public-List <public-list at lists.alberg30.org> wrote:
> 
> This is very helpful. I like the idea of not drilling any more holes, so the loop of line sounds like a good idea. How much purchase is needed on the down haul? I'm assuming it would never need a winch, right?
> 
> ________________________________
> From: Jonathan Bresler <262alberg30 at gmail.com <mailto:262alberg30 at gmail.com>>
> Sent: Monday, April 30, 2018 12:01 PM
> To: Alberg 30 Public List -- open to all
> Cc: Jon Budington
> Subject: Re: [Public-List] Spinnaker advice
> 
> Jon,
> 
> Have seen the downhaul rigged in a few different ways on various boats.
> The particular method does not seem to matter very much provided that it works for you.
> The two ways that I am most familiar with are
> 
>  *   a single block connected via a swivel to a u-bolt installed in the foredeck on centerline somewhere aft the two mooring cleats, and
>  *   a single block connected via a loop of line that passes around the aft foot of each of the two mooring cleats.
> 
> In both cases the downhaul connects to the bridle on the bottom side of the spinnaker pole via a snap shackle with a swivel.
> The line passes from the bridle through the block and back to a jam cleat near the cockpit.  Have seen the jam cleat on the side of the cabin and on the top.
> 
> The idea of using a piece of line might sound a bit, "what?", but it works well and is easily tried out without drilling any holes.
> It works well enough that TC Williams has compiled an enviable record of winning races in the Annapolis area.
> Have worked foredeck for TC for a number of years, so I've used this bit of gear for a while ;)
> 
> Jonathan
> 
> On Mon, Apr 30, 2018 at 11:34 AM, Jon Budington via Public-List <public-list at lists.alberg30.org <mailto:public-list at lists.alberg30.org><mailto:public-list at lists.alberg30.org <mailto:public-list at lists.alberg30.org>>> wrote:
> I've had Nimble for over 10 years now, and I've decided to give Wednesday night races a try. My problem is the spinnaker. I have a pole and topping lift, but I don't have a down haul. Can anyone tell me how that is rigged?
> 
> 
> Thanks,
> 
> 
> Jon Budington
> 
> Nimble
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html <http://www.alberg30.org/store/A30supporters.html>
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org <mailto:Public-List at lists.alberg30.org><mailto:Public-List at lists.alberg30.org <mailto:Public-List at lists.alberg30.org>>
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
> 
> 
> 
> --
> Jonathan M Bresler
> S/V Constance Alberg 30 #262
> Annapolis/Eastport MD
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org



More information about the Public-List mailing list