[Alberg30] Resins

[Chester and Jan Koop]

  +-------------------------------------------------------------------+
  | Wow! Save big bucks through October 31 at Sailnet's online store. |
  | Go to http://www.myaffiliateprogram.com/u/sailnet/t.asp?id=1066   |
  | and use the e-coupon code APMK18                                  |   
  +-------------------------------------------------------------------+

So would I.  Tangaroa has a hull liner and I would think that a tank located
under the cabin sole (as was discussed here on the list in February) would
work best.

Chester Koop
Tanagroa #445
----- Original Message -----
From: "John Bailey" <baileyje at voyager.net>
To: <public-list at alberg30.org>
Sent: Friday, September 29, 2000 7:18 PM
Subject: Re: [Alberg30] Resins


>   +-------------------------------------------------------------------+
>   | Wow! Save big bucks through October 31 at Sailnet's online store. |
>   | Go to http://www.myaffiliateprogram.com/u/sailnet/t.asp?id=1066   |
>   | and use the e-coupon code APMK18                                  |
>   +-------------------------------------------------------------------+
>
> I, for one would be very interested in a group buy of a custum holding
tank.
>
> John Bailey
> "Zevulun"  #33
>
> ----- Original Message -----
> From: Tom Sutherland <sutherlandt at prodigy.net>
> To: <public-list at alberg30.org>
> Sent: Friday, September 29, 2000 11:10 AM
> Subject: Re: [Alberg30] Resins
>
>
> >   +-------------------------------------------------------------------+
> >   | Wow! Save big bucks through October 31 at Sailnet's online store. |
> >   | Go to http://www.myaffiliateprogram.com/u/sailnet/t.asp?id=1066   |
> >   | and use the e-coupon code APMK18                                  |
> >   +-------------------------------------------------------------------+
> >
> > George,
> >     As usual you raise very good points.  I did think about the rough
> interior, but
> > thought it might be remedied by sloshing several coatings of epoxy
around
> the
> > interior after emptying the styrofoam. Did wonder about adhesion however
> since I
> > would not be able to remove any blush from the interior.
> >     Any merit in discussing a "group purchase" for these holding tanks ?
> I realize
> > that the group purchase idea has not always been successful but if
enough
> people
> > would be interested in a custom fit holding tank it might be worth
looking
> into.
> >
> > Tom S
> >
> > George Dinwiddie wrote:
> >
> > > Tom,
> > >
> > > I don't know if uncured epoxy will dissolve the styrofoam, or not.
> > > You would certainly end up with a very rough surface on the interior
> > > of your tank, and this would prevent it from ever being completely
> > > cleaned out.  Worse, I don't think that the epoxy laminate will be
> > > impervious to odors.  I wouldn't recommend a glass laminate, even
> > > using epoxy resin, for a holding tank.  I, personally, wouldn't use
> > > anything but HD polyethylene.
> > >
> > >  - George
> > >
> >
> >
> >
> > _______________________________________________
> >  Public-list mailing list -- Public-list at alberg30.org
> >  http://www.alberg30.org/mailman/listinfo/public-list
> >  To unsubscribe: email to Public-list-request at alberg30.org
> >  Include command "unsubscribe <password>" in subject or body.
> >  Use command "help" for more options.
> >
>
> _______________________________________________
>  Public-list mailing list -- Public-list at alberg30.org
>  http://www.alberg30.org/mailman/listinfo/public-list
>  To unsubscribe: email to Public-list-request at alberg30.org
>  Include command "unsubscribe <password>" in subject or body.
>  Use command "help" for more options.
>

_______________________________________________
 Public-list mailing list -- Public-list at alberg30.org
 http://www.alberg30.org/mailman/listinfo/public-list
 To unsubscribe: email to Public-list-request at alberg30.org
 Include command "unsubscribe <password>" in subject or body.
 Use command "help" for more options.

 970459585.0