[Public-List] Getting mast wires into the boat?

[Meinhold, Michael J.]

I agree - I am probably more noise-sensitive then many, but the slap of
the wires drove me crazy.

I did the same wire-tie trick and it's completely silent.

Mike
Rinn Duin #272

-----Original Message-----
From: public-list-bounces at lists.alberg30.org
[mailto:public-list-bounces at lists.alberg30.org] On Behalf Of Jeffrey
Sent: Thursday, August 29, 2013 3:06 PM
To: Bill Wallace
Cc: Alberg 30 Public List -- open to all
Subject: Re: [Public-List] Getting mast wires into the boat?

Thanks Bill.

I'll likely do the same thing. And I think you are right about the self
amalgamating tape over whatever bundle of wires would stop most water.

RE: I rewired my mast a couple of years ago and also used the cable tie
trick. We used maybe 100 cable ties, but the wires inside are silent!
It's been two seasons now and still not a peep. Works great.  Great bang
for your buck on that fix.

jeff



On Thu, Aug 29, 2013 at 2:45 PM, Bill Wallace
<wayfarer3134 at yahoo.com>wrote:

> I use the slightly larger than single wire sized cable clam to get 4 
> wires
> - a triplex, two duplex and a round vhf wire so that I can disconnect 
> everything in the winter when the mast gets removed.  It seems pretty
dry.
>  I'd probably freeze it though for the initial drilling - and it is 
> really painful getting the wires through initially, as at least for me

> it was a fairly small hole I used.  You could probably wrap the wire 
> with butyl tape to ensure a totally watertight pass through the rubber

> stopper.  I'm planning on redoing it this winter as the VHF cable is 
> spliced twice and I'd like a better set of disconnects inside the boat

> and at the top of the mast to allow me to remove the wind instruments 
> cleanly every winter.  The wires also bang inside the mast so I plan 
> on wrapping several sets of 3 cable ties to keep the wires centered 
> and prevent banging (every 3' roughly you wrap 3 cable ties with the 
> ends at 120 degrees to each other and preventing the cable from 
> slamming against the wall of the mast.)
>
> Bill.
>
>   ------------------------------
>  *From:* Jeffrey <fongemie at gmail.com>
> *To:* Alberg 30 Public List -- open to all 
> <public-list at lists.alberg30.org>
>
> *Sent:* Thursday, August 29, 2013 2:18:23 PM
> *Subject:* [Public-List] Getting mast wires into the boat?
>
> Hi everyone,
>
> I'm wondering what everyone else has set up to get the wires from the 
> mast into the boat?
>
> I have a setup on #116 where someone has drilled a hole through the 
> mast step plate, through the mast beam and it comes out just inside in

> the v-berth just forward of the beam. A stainless tube was inserted 
> and the wires from the mast are run through this tube, into the boat 
> cabin to a connections box. It's a clean setup from the outside, 
> however we've discovered that unless you get a good drip loop in the 
> wires at the mast base water can flow down into cabin and drip on the 
> floor. And, the sll the wires into the tube is a tight fit.
>
> I'm about to remove my mast beam completely, and laminate a new one 
> out of sapele (or perhaps white oak). I think I'd like find a 
> different solution for the wires to exit the mast through a hole, then

> into the cabin top via some fitting of some sort.
>
> I've used the Cable Clam type fittings with success for single round
> cables:
>
> http://www.jamestowndistributors.com/userportal/show_product.do?pid=66
> 1&familyName=Perko+Watertight+Cable+Outlets
>
> I wonder how those would work for multiple wires and duplex covered
wires?
>
> What do you all do??
>
> I hope everyone is having a great season.  We decided to skip putting 
> our boat in the water to get some house and boat projects done, can't 
> wait until next season already.
>
> -jeff
>
> Seagrass #116
> Boothbay Harbor Maine
>
> --
> ______________
>
> Jeffrey Fongemie
>
> <http://instagram.com/jfongemie>
>
>
> <http://instagram.com/jfongemie>
> _______________________________________________
> These businesses support your Association:
> http://www.alberg30.org/store/A30supporters.html
> Please support them.
> _______________________________________________
> Public-List mailing list
> Public-List at lists.alberg30.org
> http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org
>
>
>


--
______________

Jeffrey Fongemie

<http://instagram.com/jfongemie>
_______________________________________________
These businesses support your Association:
http://www.alberg30.org/store/A30supporters.html
Please support them.
_______________________________________________
Public-List mailing list
Public-List at lists.alberg30.org
http://lists.alberg30.org/listinfo.cgi/public-list-alberg30.org

 1377803372.0